Find the "Reply to Thread" and click on it.
It will load the reply box.
The red arrow in the attached image is pointing to the insert image icon.
7932
Type: Posts; User: Bob
Find the "Reply to Thread" and click on it.
It will load the reply box.
The red arrow in the attached image is pointing to the insert image icon.
7932
And, if you're looking for snap off the line drop in a 2-2500 rpm stall converter.
Wire it up and see if it still make the noise.
It is hard to imagine that it would not include the main seals as it is a "full" set.
I found a couple of images of what is supposed to be in the set, and they both show the rope seal. Images can...
I thought I would bring up a subject which has been touched on elsewhere on the web, but is still unclear. I was just going to make it an article, but thought I would place it here for a while to...
GM did not offer a single post alternator in '66. You might try Part number 80500, GM 63 amp 1 wire alternator.
GM single post alternator, 80500...
My car does not have a consul which should mean it takes the same boot. It is a single boot with a stainless trim hold down. I believe they are common to a-bodies a few years either side of '67....
They max. tolerances are in the '67 manual, and are the same as the '69 manual. The '67 manual brake section is here:
https://www.teambuick.com/reference/library/67_chassis/files/50-a.php...
1969 is the same as 1967.:thumbsup:
I would use the one you prefer. I use a satin black in a can, or have the mixer put a little flattener in a single stage.
I would have simply described the effects of a spacer are to increase the rpm range of the engine. That can be interpreted as it will increase power at higher rpm, usually about +1000 rpm, but it...
You don't have to add a spacer to increase performance of a stock manifold. You can remove most of the center plenum as done by "Doc" with his 2X4 manifold here:...
What I see as a problem with the Performance Group air cleaner is the base. The base in the Buick version is formed to fit tightly over a Rochester carb and to use a smaller diameter filter than you...
Won't make any difference, but the transmission and the Rochester almost make it sound like someone may have slipped in a package from a '66. Have you ID'd the engine?...
Other sources are:
Buick Riviera Exhaust System on Ebay...
Here you are:
7812
telriv
You can find him as telriv in the Community/Members list
or here is a link to his profile CLICK HERE
It's on the road!
https://youtu.be/xUIncQwfj7Q
If any Straight Eight enthusiasts have any information that they can add to the Blue Printing section of the "Straight Eight Engine Specifications" please post them.
The blueprint specifications...
Probably not much help, but:
According to my Hollander, the '54-56 56R, 76R, 76RX Riv. Cpe use vent glass 1022 which is shared with '54-56 Cadillac 62 Cpes. exc. Conv.
These may be them on...
I think I may have plugged up the site, it should be good now:(
This might be a new cap on Ebay
Buick carburetor start switch...
Larry70GS posted a picture near the middle of your first post page that shows the transmission switch. It is on the driver's side above the transmission oil pan.
It has two prongs running opposite...
Sounds like a problem I am about to tackle:)
I have a beautiful mandrel FlowMaster system on my '66 Riviera, my daughter wanted the "sound". I am going to be driving it and have just purchased a...
If you switch is there, follow the "How to wire the Switch Pitch on a Buick Transmission" link at the top of this page.
Here's some on Ebay:
Buick kickdown switch...