Search results

Bob, Are you going to Spokane? I know it is a little late as I am leaving in the morning for Spokane. What car are you driving? I will be in a maroon 52 Buick woodie wagon with Oregon plates.

I have a 66 turbo 400 Buick transmission behind a 425 nailhead. I had the switch pitch torque convertor rebuild. Can I drive it for a 1,000 miles without hooking up the switch pitch assembly? Which position is the torque converter in if not wired up to electricity?

I have a 52 Buick Super which was involved in an accident last September. The front suspension and both front fenders, inner fenders and hood were destroyed. I put a new subframe on it. I located replacement fenders and hood. I had them painted and now I am getting ready to install them on...

I had lap belts in my car but after my wreck I decided to install 3 point belts in the front. My Buick is a 1952 four door station wagon. Has anyone had experience and can recommend a good supplier?

I am using a long neck water pump out of a 1959 401 engine. I would like to put a fan clutch on this engine. The bolt pattern that Buick used to attach fan to water pump was 4 bolts X 1 ¾ inch bolt pattern. Hayden Cooling Products does not have a fan clutch with that pattern. Does...

suntreemcanic submitted a new listing: Edmonds Dual Carburetion Intake Manifold - Edmonds Dual Carburetion Intake Manifold View the entire listing here...

Do 248 and 263 intake manifolds interchange?

suntreemcanic submitted a new listing: 1948-1949 Buick Shop Manual - 1948-1949 Buick Shop Manual View the entire listing here...

My 52 Buick Super was converted to 12 volts years ago. I used a voltage reducer for the heater and defroster motors. This method worked good till today when my heater motor just locked up. Were 53 Roadmaster or Super heaters under the front seat like 52s. Does anyone know if they are...

Where is Bob?

suntreemcanic submitted a new listing: Power steering 52 super straight eight - Power steering 52 super straight eight View the entire listing here...

I am working on 2000 Land Rover with a 240 CI aluminum engine. Is that a Buick motor that has been enlarged from 215 CI? Does rocker arm parts from a 215 interchange with the 240 such as plugs in the ends of the rocker arm shaft? Land Rover parts are hard to find and expensive. Buick parts...

I am working on a 1952 Buick Super. I relocated my fuel tank to the passenger side of the car. The tank came from a Buick Special and the neck was always short and I had trouble filling it in California. When you open the fuel fill door how much lower is the top of the fuel fill neck than the...

I have put together a 425 Nailhead and installed it in a 1952 Buick woodie station wagon. The block is a 1966. The intake is a 1963. The heads are 1959. I have the engine running and it was balanced. The cam is a mild version for torque. I bought a new Edelbrock 800 CFM carburetor. It has...

suntreemcanic submitted a new listing: Parting out 52 Roadmaster - Parting out 52 Roadmaster View the entire listing here...

suntreemcanic submitted a new listing: Flywheel Cover - Flywheel Cover View the entire listing here...

I know this forum caters to the "leave it like it came from the factory" crowd and I left my '52 Buick stock for 33 years but it just can not keep up with traffic so I am installing a 425 nailhead in it. I decided to go with rack and pinion steering and that required me to modify my steering...

I am trying to run my new rebuilt 425 engine on an engine stand. To get the water pump to work I thought I could use some 401 generator mounts from a 1959 that I have, and mount a generator then I could adjust a belt to turn the water pump. I have the Master Parts book but can not find a...

suntreemcanic submitted a new listing: Nailhead 425 Pistons - Nailhead 425 Pistons Learn more about this listing...

suntreemcanic submitted a new listing: Eaton Posi. Rear end - Eaton Posi. Rear end Learn more about this listing...