Results 1 to 4 of 4

Thread: I’m an old -71 Buick skylark owner

  1. #1
    Join Date
    Sep 2018
    Location
    Sweden
    Posts
    2
    Rep Power
    0

    I’m an old -71 Buick skylark owner

    Hi!
    I’m an old -71 Buick skylark owner.
    I owned this Buick longer then I has been married to my wife, but she (the woman) and I was “together” before I bought the car…
    It’s a 350 car with a -68 PP (4-bbl 10:1) engine. (Stock -71 2bbl in garage with bad crank)
    It got a crane cam and dough’s headers Holley 650 spread bore vac sec carb. with 50cc acc pump. And a 2” 4 hole spacer
    Dave Ray/ Ignition Man instruction rebuild to full int. vac and recurv distributor with crane “pointless” kit.
    Blocked exhaust passages to intake
    TH350 with “lose” converter prox. 2200-2400 stall. 3:08 lim slip rear end still on 14” rims to get higher engine rpms (cheaper and simpler than changing rear axle “again” vas like 2.92 open?)
    Crossover pipe on dual exh.
    Disk front brakes. (Was drums)
    Added the headers late this summer, but not happy with them as I lost too much ground clearance..
    Some one at that factory is not the sharpest knife in the box, placing one of the collector bolt holes at 6 clock (down lowest)
    –the collector flange is welded to the header and I did not think much of that until it touched / kissed the ground when I backed out from the driveway first time..
    And I got 12 1” + 2 ¾ bolts instead of 14 1” bolts as in there instruction/packing list and they don’t answer my e-mail when I try to get them to send me 2 more 1” bolts. The ¾ don’t work – to short. had to use 2 1" hex head bolts
    I join this forum as I can see and read a lot of info here.
    -I think there is a lot of good info. Here, and as I’m about to “go 455” in the “ragtop” I need all help to not do all possible mistakes!
    Snowmad

  2. #2
    Join Date
    Mar 2008
    Location
    Kent, WA
    Posts
    120
    Rep Power
    0
    If you decide to go with headers on your 455, I would recommend TA Performance's shorty headers. That is what I am running on my 69 that has been lowered 2 inches in the front.

    http://www.taperformance.com/products.asp?cat=387

  3. #3
    Join Date
    Sep 2018
    Location
    Sweden
    Posts
    2
    Rep Power
    0
    that's god to know.
    is TA the only manufaktuer of shortys?
    i don't have a problem with TA, but "competition is Always god for price"

  4. #4
    Join Date
    Aug 2015
    Location
    Oakland Ga
    Posts
    133
    Rep Power
    0
    Yes, TA is the only one.
    Larry

    1970 GS455 Stage1 Race weight 4025 lbs.
    TSP 470, 602 HP, 589 TQ
    MT headers, Gear Vendors Overdrive
    Best E.T. 11.54 Best MPH, 116.06
    1998 Riviera SC3800

Similar Threads

  1. New '70 Buick Skylark owner
    By Bama Jama in forum New Member Introductions!
    Replies: 8
    Last Post: 08-15-2016, 11:21 PM
  2. new 66 Skylark owner
    By inda_bebe in forum New Member Introductions!
    Replies: 3
    Last Post: 06-08-2015, 04:41 PM
  3. New Buick owner 64 Skylark
    By Tintman in forum New Member Introductions!
    Replies: 4
    Last Post: 09-17-2014, 11:22 AM
  4. New 1970 Buick Skylark Conv. owner
    By Jim T. in forum New Member Introductions!
    Replies: 2
    Last Post: 06-15-2011, 01:22 AM
  5. New Buick Owner! My 1969 Skylark...
    By Kojack in forum Buick Bench Racing and Chat
    Replies: 3
    Last Post: 07-11-2010, 11:46 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
TeamBuick.com Privacy Policy