From the Reference Section:
- How to choose your new wheels and tires
- Buick Rallye Wheels
- Calculators: Tires, Gears, MPH, etc.
- Wheel Bearing Adjustment, 1963 - 1970
Results 1 to 7 of 7

Thread: Help , cannot diagnose vibration

  1. #1
    Join Date
    Jul 2009
    Location
    Danbury, C
    Posts
    3
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0

    Help , cannot diagnose vibration

    Light vibration at 60 to 70 mph , none below 60, slightly better over 70. can drive but uncomfortable(2500 miles since construction), coasting in neutral makes no difference, braking no difference, turning no difference

    Sorry to bring this up because I know there so many opinions and variables but i am desperate! Here goes:
    1956 Buick Special 2 dr sedan: see pix
    rebuilt stock front suspension
    1965 401 motor rebuilt- stock rubber motor mounts on fabricated steel mounts
    Muncie m20 4 speed, Wilwood hydraulic clutch linkage
    Disc brake conversion/ Scarebird
    87 GN rear rebuilt replaced axels- Four link rear suspension with stock springs and panard bar
    custom built drive shaft - balanced and re-balanced twice- no difference
    tried 4 sets of wheels and tires and combinations no difference/ has 1" adapters to change bolt pattern on rear axle. Have run with stock wheels and tires / no diff
    slight play in yoke to transmission - rebuilt no difference
    pinion angle checked at 4 wheel drive extreme vehicle shop (they think it is driveshaft) also checked the frame for straightness& track =ok
    tried to put hose clamps on driveshaft, could not eliminate vibration
    have not replaced brake drums
    What is NEXT STEP? DESPERATE!
    Attached Images Attached Images

  2. #2
    Join Date
    Dec 2013
    Posts
    286
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0

    Viberation

    If was me,I would pull the drive shaft and have it checked. May also be the clutch, but that should be engine speed noticeable rather than road speed.

    Nice car.

    Ben

  3. #3
    Join Date
    Feb 2009
    Posts
    101
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0
    Did you test in 3rd gear?
    If it was not a custom driveshaft, I would recommend swapping a known good one...you may have to have another fabricated.
    I had that problem after replacing U-joints (originals were glued in). Apparently the driveshaft was damaged during removal, because a junkyard shaft cured the vibration.
    Check the engine rpm when vibrating the most and then again (same rpm) sitting in neutral and then with the clutch depressed.
    (hard to do safely: tow up to speed with the driveshaft removed.)

  4. #4
    Join Date
    May 1999
    Location
    A, B
    Posts
    3,311
    My Feedback

    (0% Positive Feedback)
    Rep Power
    10
    As you suspect, your brake drums could be way out, also axles can be a problem if they are bad enough. Try to ensure the problem isn't in the engine area as suggested.

    Was the engine balanced? What did you do for a flywheel when coupling the M21 to the externally balanced 401?


    WEBNOTE: When inserting an email in a posting, use the "smilie" @ so that web robots don't pick up your address and send you more junk mail!
    Members can be contacted by clicking on their "handle", but you are much better off to post to the thread!



  5. #5
    Join Date
    Jul 2009
    Location
    Danbury, C
    Posts
    3
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0

    thanks

    Thanks . rear has been checked and rebuilt, I have run it on a lift with wheels up but at ride height... can see vibration but cannot find where it is coming from.. thanks for help. Getting closer to drive shaft replacement.

  6. #6
    Join Date
    Nov 2008
    Location
    Sisters OR
    Posts
    416
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0
    I will go in another direction. Are the tires in balance? Can you exchange wheels and tires from another car? What condition are the shocks in?

  7. #7
    Join Date
    Sep 2015
    Location
    Halstad,MN
    Posts
    19
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0

    Vibrations

    One more thing you may wanna check is your rear tail housing bushing. If that is worn it will allow the yoke on the driveshaft to move in a oblong manner feeling like a front u joint is going out. This does usually show up around the speed you're talking about.

Similar Threads

  1. Engine Vibration
    By 64TA-Skylark in forum Big Block: 400, 430, 455
    Replies: 5
    Last Post: 11-20-2012, 11:43 AM
  2. Straight 8 Vibration
    By 1953Special in forum Straight Eights!
    Replies: 20
    Last Post: 10-18-2012, 09:46 AM
  3. Please Help Diagnose 53 Roadmaster Overheating
    By 4est in forum Heating and Cooling, Radiators
    Replies: 6
    Last Post: 11-17-2010, 12:03 AM
  4. Engine Vibration
    By jim harrell in forum V-6, early and late...
    Replies: 3
    Last Post: 11-24-2009, 02:11 PM
  5. Driveshaft vibration
    By John Payan in forum Transmissions and Drivelines...
    Replies: 0
    Last Post: 12-04-2006, 03:44 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •