From the Reference Section:
- Buick Cams from Kenne Bell, 252, 231, 225,198, 196
- 225 V-6 Engine Specifications
    - 2 Less = More, Stage II V-6
- The Baker Buick V-6
Results 1 to 8 of 8

Thread: Buick V6 engine identification

  1. #1
    Join Date
    Apr 2017
    Location
    Eagle, CO
    Posts
    7
    Rep Power
    0

    Buick V6 engine identification

    Hi - This is Jim. I purchased a 1963 Willys Station Wagon with a transplant GM (I think Buick) V6 and I'm trying to accurately identify the year of the engine. The number on the intake manifold above the bell housing is B-1376389. The number on the block below the driver side head is K-130023. There is also a number on the head under the valve cover that starts with GM. I haven't got the full number. Can anyone help me identify this engine. For what's it's worth it has a Holley series 2280 carburetor on top. Thanks - I appreciate your help - Jim

  2. #2
    Join Date
    Sep 1999
    Location
    Dbl Oak,TX
    Posts
    745
    Rep Power
    25

    Smile

    Jim, the characters stamped into the block are the best way to identify these engines. See attached page from the '74 Chilton repair manual Jeep chapter. This shows the 1967-71 Buick/Jeep V6 codes. Another site, www.earlyCJ5.com indicates there is a third letter in front indicating Domestic/Military/Export. Then there will be 3 numerals at the end for date of production. A Buick V6 of the '60s built for car usage will have only 2 letters then 3 digits. Those engines can be decoded from the Reference section on this site.

    The assumption so far is that the engine dates from this period. The manifold casting number looks close to other Buick casting numbers of this time. These early V6s use a distributor with breaker points. The cap will be the odd-fire design that looks like an 8-cylinder cap with 2 of the posts blanked off. Engine will not have much pollution equipment on it either. Does this sound like yours?

    It could also be some later Buick V6 from a car. Features would typically be HEI pointless electronic distributor, regular even-fire 6 post cap, more pollution equipment. Although it might not be original to the engine, we can examine the distributor part number.
    Attached Images Attached Images
    Last edited by TODD; 10-24-2017 at 05:06 PM.
    What has been, can be again. (Bob Wills, 1942)

  3. #3
    If it should be a Buick v-6, the location of the identification numbers can be found here:
    https://www.teambuick.com/reference/...gine_where.php


    WEBNOTE: When inserting an email in a posting, use the "smilie" @ so that web robots don't pick up your address and send you more junk mail!
    Members can be contacted by clicking on their "handle", but you are much better off to post to the thread!

  4. #4
    Join Date
    Apr 2017
    Location
    Eagle, CO
    Posts
    7
    Rep Power
    0

    V6 Identification

    Thanks Todd - I'm finally getting back to the project and will look for the places you identified to see what numbers I come up with. From all the other information about the engine I'm fairly certain it's a 1963-1966. Thanks - Jim

  5. #5
    Join Date
    Aug 2018
    Location
    Kansas Cit
    Posts
    2
    Rep Power
    0
    Quote Originally Posted by TODD View Post
    These early V6s use a distributor with breaker points.
    True.
    The cap will be the odd-fire design that looks like an 8-cylinder cap with 2 of the posts blanked off.
    Not true.

    On the oddfire V6's with points, they will have either a Prestolite or a Delco distributor. Both use a regular-looking smallish (non-HEI small) distributor cap with 6 evenly spaced plug wire towers (60° spaced). Only the HEI distributors in the later 231 motors had the large caps with a couple of 'blank' towers. To account for the rotor on the 'points' type distributor not really lining up perfectly with the individual towers, the rotor has an elongated tab to transfer the energy to the distributor cap towers, such as in this picture:

    13a.jpg

    The HEI caps used a regular-looking rotor with the elongated 'tabs' on the underneath of the distributor cap (instead of on the rotor, but accomplishing the same thing).

    I know the thread is a few months old, but I keep reading that 'if the distributor has even towers, it must be an even fire), which is not the case. Been keeping my old 225 odd-fire running for 30+ years, so I have a little bit of first-hand knowledge.

  6. #6
    Join Date
    Apr 2017
    Location
    Eagle, CO
    Posts
    7
    Rep Power
    0

    Good Description

    Thanks EchoWars - Your description of the distributor cap is exactly what I have. After some parts searching and roundabout reasoning I've determined this engine is a 1966 Buick V6 that runs well after sitting outside and not being run for at least 10 years. It should do well in powering the 1963 Willys wagon.

  7. #7
    Join Date
    Sep 1999
    Location
    Dbl Oak,TX
    Posts
    745
    Rep Power
    25
    I should have denoted that correctly. Time for 6 lashes with a wet shop manual
    What has been, can be again. (Bob Wills, 1942)

  8. #8
    huh.

    i missed the Jeep engine codes last year. dur duh duh dur.
    The way to crush the bourgeoisie is to grind them between the millstones of taxation and inflation.
    Vladimir Lenin

    Government schooling is about "the perfect organization of the hive."
    H.H. Goddard, Human Efficiency (1920)

Similar Threads

  1. 1955 Buick engine identification problems
    By RB in forum Buick Identification and Decoding
    Replies: 1
    Last Post: 11-21-2015, 09:05 AM
  2. 1934 Buick Series 40 engine identification
    By Doug H in forum Straight Eights!
    Replies: 11
    Last Post: 01-26-2013, 06:25 PM
  3. Identification of Buick V6 Engine
    By john s in forum Buick Identification and Decoding
    Replies: 2
    Last Post: 07-22-2007, 04:15 PM
  4. Identification of Buick V6 Engine
    By john s in forum Buick Identification and Decoding
    Replies: 5
    Last Post: 07-22-2007, 09:53 AM
  5. Buick engine identification
    By bigsilver in forum Buick Identification and Decoding
    Replies: 4
    Last Post: 01-03-2004, 07:39 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
TeamBuick.com Privacy Policy