Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: Re-motoring a lakes bucket style street rod project called Cassi.

  1. #11
    Join Date
    Dec 2013
    Posts
    305
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0

    Clarification. Hopefully

    Glad to see the work progressing.

    I have never heard the side mount thing started mid year. Maybe so. From my knowledge and what I see. Side mounts started in '48, your engine has none, therefore a '47 or earlier. Other than mounts, I believe no difference. Still a 248.
    Insert rod bearings started in 1949.
    First 263 was 1950.
    All 248 had increasing size main bearings, front to back.
    All 263 had same size main bearings, front to back.
    Your rods can be machined to accept inserts. Relatively inexpensive, I
    believe.
    If you will post the engine #, the year can be confirmed. Besides being on the side of the engine just in front of the distributor , it is on the front beneath the water pump, in that bluish area on the front of the engine.

    I really like this project.

    Ben

  2. #12
    Join Date
    Sep 1999
    Location
    Dbl Oak,TX
    Posts
    578
    My Feedback

    (0% Positive Feedback)
    Rep Power
    19
    The Buick Master Parts book confirms the change to side-mounted motor mounts began at the start of the 1948 model year at engine no 4999881. It also shows the 248 crankshaft introduced in 1941 was continued on with the same part number thru the last 248 in 1950.

    The changeover to full-precision insert main bearings occurred mid-year 1947 after a trial run of some 1200 engines earlier that year. Another mid-year change occurred in 1946 to introduce semi-precision main bearings. So if it's a 1946-47 engine it could have one of three types of main bearings. Attached is a 1947 dealer service bulletin giving the engine number break points and markings for the various bearings.
    Attached Images Attached Images
    What has been, can be again. (Bob Wills, 1942)

  3. #13
    Join Date
    Dec 2013
    Posts
    305
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0

    Mid year changs

    Thank you ,sir. Did not know that. I am not sure I understand semi precision and full precision.

    Am I correct on the rod bearing change? I sure do not want to mislead anyone.

    Ben

  4. #14
    Join Date
    Nov 2016
    Location
    L.A.
    Posts
    17
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0
    Thank you, Gentlemen. As a Tyro to this engine I truly appreciate any help you're willing to extend.

    So, the number on the front is 3820977, and the side is 53820977 (I'm guessing the added "5" denotes something other than bearing information). While not specifically among the numbers you were kind enough to supply, am I correct in reading this as pre-'46, and in supposing I'll find Babbitt mains inside?

    Also, the side number on the 263 is b1888885 (the water pump's still blocking the front pad on that one). I'm hoping the front plate mount holes, the bell mounting holes, and the crank flange are the same as the 248, so that I'd be able to swap it directly in at a future date. Is that hope warranted?
    Sex, drags, and rock & roll.

  5. #15
    Join Date
    Dec 2013
    Posts
    305
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0

    Engine number

    Well, the 248 you have is a 1940.

    The 5 on the side number can be ignored. Through 1942, all Buick engines were numbered with the series # first. 4 for 40 series, Special. 5 for 50 series, Super. The second digit is the start of the actual engine number for that series. The 5 says your engine came from a Super.
    1940 engine numbers began with [5] 3,786,214
    1941 4,074,859
    Your number, 3,820,927 falls in between those, so it is a 1940. Babbitt rod bearings.

    The 263, which came out in 1950, is a 1950. Beginning in 1946, the series digit was moved to the end of the serial #. 1951 #s started with 6,240,100. Your #, 6,188,888 comes before that. So, it is a 1950, 263 .

    The front of the engines are all the same. The front plates will interchange. The crank, if the 263 came from a standard car, is the same at the back. If from a Dynaflow car, you will need to alter it as you have done the 248.

    Hope I have helped.

    Ben

  6. #16
    Join Date
    Nov 2016
    Location
    L.A.
    Posts
    17
    My Feedback

    (0% Positive Feedback)
    Rep Power
    0
    Indeed you have, very useful. Thank you.

    If the 248 runs acceptably I'll leave'er in for the set-up and initial sorting out, work over the 263, and swap that in when it's ready. With a bit of luck I may yet have'er back on the street this year.
    Last edited by Old6rodder; 02-15-2018 at 12:00 PM.
    Sex, drags, and rock & roll.

Similar Threads

  1. Another Newb. (Engine swap in a street bucket.)
    By Old6rodder in forum WELCOME forum!
    Replies: 5
    Last Post: 12-06-2016, 09:40 PM
  2. Replies: 1
    Last Post: 08-10-2014, 10:44 PM
  3. body style help
    By coaster in forum Buick Identification and Decoding
    Replies: 0
    Last Post: 11-05-2007, 04:27 PM
  4. dynaflow to new style 401
    By garaget401 in forum Nailhead: 264, 322, 364, 401, 425
    Replies: 0
    Last Post: 11-24-2005, 03:56 PM
  5. Lake style headers?
    By Buford26 in forum Straight Eights!
    Replies: 1
    Last Post: 04-24-2005, 05:50 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
TeamBuick.com Privacy Policy