Search:

Type: Posts; User: telriv

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    2
    Views
    703

    I have a front & rear pair from a '65 Riv GS I...

    I have a front & rear pair from a '65 Riv GS I just removed to install new springs into. Funny thing is the replacement springs actually brought the front & rear ride height down instead of up. I...
  2. Replies
    24
    Views
    1,584

    That relates to a '63/401 cubic inch engine with...

    That relates to a '63/401 cubic inch engine with the 4 bbl. carb. Rated at 325 HP @ 4400 rpm's & 445 t. lbs. of torque @2800RPM's. Advertised compression ratio is 10.25-1. In reality closer to...
  3. Replies
    24
    Views
    1,584

    That relates to a '63/401 cubic inch engine with...

    That relates to a '63/401 cubic inch engine with the 4 bbl. carb. Rated at 325 HP @ 4400 rpm's & 445 t. lbs. of torque at 2800RPM's. Advertised compression ratio is 10.25-1. In reality closer to...
  4. Replies
    1
    Views
    174

    NO I do have a just about a perfect '66...

    NO

    I do have a just about a perfect '66 WildCat grille for sale. Not cheap
  5. If I remember correctly Buick started using the...

    If I remember correctly Buick started using the X-Frame in 1938 & didn't stop until 1970 with the Riv.
  6. Replies
    13
    Views
    6,145

    Look up "Jacob" in this forum

    Look up "Jacob" in this forum
  7. Are the rear brake shoes adjusted properly???

    Are the rear brake shoes adjusted properly???
  8. The way I do the pumps is cleaning up the casting...

    The way I do the pumps is cleaning up the casting flash inside on the cast pumps for better oil flow. The aluminum pumps are more finicky but, some people like those better. For the pick-up tube you...
  9. Just go to your local hardware store, take the...

    Just go to your local hardware store, take the new pump with you, & get a 1/2" NPT (I believe that's the size) plug in the plumbing dept. If your unsure ask for help. Put some thread sealer on the...
  10. Replies
    1
    Views
    1,744

    A pic would be VERY HELPFUL.

    A pic would be VERY HELPFUL.
  11. Thread: Intake manifold

    by telriv
    Replies
    3
    Views
    2,105

    A pic would be VERY HELPFUL.

    A pic would be VERY HELPFUL.
  12. 1st. off if a Buick engine the distributor will...

    1st. off if a Buick engine the distributor will be in the front. To tell if it's a big block or small block all you have to do is look at the valve covers. 5 bolts holding them down is a 455. 6 bolts...
  13. Replies
    1
    Views
    1,472

    Speedo has to come out. More than likely the gear...

    Speedo has to come out. More than likely the gear fell out of place.
    Try a linkage adjustment 1st. If you don't have one get a CHASSIS MANUAL.
  14. Replies
    5
    Views
    285

    Try FATSCO

    Try FATSCO
  15. Replies
    13
    Views
    1,704

    I used to have one EXACTLY like that. Gun Metal...

    I used to have one EXACTLY like that. Gun Metal Gray 3 speed on the colunm.
  16. Replies
    1
    Views
    1,600

    MANY vendors in Hemming s.

    MANY vendors in Hemming s.
  17. Replies
    11
    Views
    3,112

    Chris, You will NEED a rear sump oil pan &...

    Chris,

    You will NEED a rear sump oil pan & matching pickup. GS specific exhaust manifolds. Re-wiring of engine compartment. Bigger radiator & cooling fan & shroud. GS specific motor mounts &...
  18. Intake manifold is for '65-'66. '64 would end in...

    Intake manifold is for '65-'66. '64 would end in a 106
  19. '64 TH400's DID NOT have switch pitch converters...

    '64 TH400's DID NOT have switch pitch converters the 1st. year.
  20. Replies
    3
    Views
    1,992

    I rebuild, recurve & install one wire electronic...

    I rebuild, recurve & install one wire electronic conversions. NO ONE KNOWS except you & I. After doing them for 12 yrs. Have had NO failures.
  21. Replies
    4
    Views
    2,159

    Not easily

    Not easily
  22. Replies
    6
    Views
    1,564

    Cyrtis, You could rebuild & install a...

    Cyrtis,

    You could rebuild & install a 401/425 "Nail" in there & MANY wouldn't be any wiser. I know a few that has installed the older Big Block Chevs & ALL were not PRETTY!!!
  23. Replies
    7
    Views
    2,171

    Thin/skinny hands/arms help tremendously in this...

    Thin/skinny hands/arms help tremendously in this instance.
  24. Replies
    4
    Views
    773

    Ben, I'm VERY glad to hear that!!! I DO...

    Ben,

    I'm VERY glad to hear that!!! I DO try my best to give anyone what they are looking for & one of the MOST important things to me is your satisfaction!!!


    Tom T.
  25. Thread: Dynaflow 1961

    by telriv
    Replies
    1
    Views
    678

    The torque converter was improperly assembled.

    The torque converter was improperly assembled.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
TeamBuick.com Privacy Policy