Hey All, Any clue if a 67 Electra column will fit a 67 Lesabre coupe? Something tells me that with the longer wheelbase of the Electra it will be too 2-3" too long.
I guess I'll see when it arrives...
Type: Posts; User: Tommie
Hey All, Any clue if a 67 Electra column will fit a 67 Lesabre coupe? Something tells me that with the longer wheelbase of the Electra it will be too 2-3" too long.
I guess I'll see when it arrives...
Does anyone have a source for the lower body trim that runs below the doors on the rockers between the wheel wells on 67 LeSabre coupes?
I think it's about 1/2'' wide stainless or aluminum.
...
Still looking but my research says an off the shelf harness from Painless is the way I may go.
Hello, does anyone have the thin chrome/aluminum side spears that mount below the doors between the wheels on both sides on the rockers. They are 3/8-5/8 wide and held on with blind chips...
Thanks
Doug,
Nice folks over at M&H. After speaking with them, they may offer the main harness and fuse block in the future but they aren't making now. Product range doesn't even include components to...
Thanks for the help. M&H has pieces but not the whole harness with fuse block. I need a "headlight to tail light" harness package
Manual does cover, but my entire harness and fuse block is toast. Has anyone used a Painless setup on 67 Full Size?
Hello All.
Does anyone have as source for a engine harness for 67 LeSabre? Car is being restored with the stock 340 -4 drivetrain. Looks like a universal Painless 21 circuit the will work for the...
Hello,
Anyone have a nice clean passenger side lower quarter?. Coupe or sedan is okay.Can't afford a whole one from AZ!
Thanks
Tom
These seats look to be AMC Concord sourced. Perhaps early 1980's
Does anyone have photos of the bodymounts at the rear quarters? An actual 67 -68 LeSabre/Wildcat to lay eyes on here in NJ would be good to!
Mine were replaced with an old fender section and a...
Does anyone know if 68 T400 trans lines are the same as 67 for LeSabre? Inline Tube only has them for 68. Only major difference is the 67 had a 340 and the 68 had the 350. I'm hoping the routing is...
Hey, I have an NOS driver's side quarter for a 4 door 68 LeSabre. Found it on ebay and it will work for my 2 door 67. If you find a coupe panel I'll be happy to trade!!!
Hey all, does anybody know if the chrome AC vent ***** that the 1966/ 67 Chevy cars and trucks are the same as those for my 67 Lesabre? They sure look the same in photos! Are the rectangular center...
Does anyone have a source for mufflers? The old replacement units (convert to duals) I took off the car are:
Shell Length 18"
Shell diameter 4 1/2" x 10 3/4"
Inlet/outlets 2 1/8 "
inlet and...
You are 100% correct! Went on only one way. Thanks so much.
I just removed the Guidematic from my 67 LeSabre. I believe it may have been dealer installed. Reads Model is 466 (4 means Buick , 66 could be the year) and the photo eye was mounted in the center of...
Can't seem to remember how to index my flex plate to my crank. Flex has two large oval holes and one "smile"cut out so it's not uniform. Does anybody have a clue...
Thanks
Tommie
Hey, I 'm looking for a front sway bar for my 67 LeSabre. Addco is a company that's all over ebay. They make new sway bars for lots of Buick applications. A front unit for my car is $197. Kinda...
Hey all.. Does anybody know if these rears were painted black? I can't find the slightest hint of paint anywhere! Even after I removed the gloppy dealer under coat, nothin' . The yellow NJ letters...
Looking for a complete front seat or better yet a twin bucket seat set with fold down arm rest like a Riv.
Thanks!
Tommie
Hey-- Does anybody have a source for the lower control arm bump stops for 67 LeSabre? Uppers ain't so easy to find either but I did locate those on Energy Suspension.com.
They are listed for 1978...
Does anyone know how tight to make the upper ball joint 2 1/4 inch nuts that secure them to the arm?. I suppose pretty tight with a little lock-tite....???
Thanks
Tom
I have photos of mine before I took them apart and can email direct to you. My email is tcang@yesstandard.com.
Tommie
Hey, does any body out there have a squirrel cage blower wheel for a 67 Lesabre?
It seems all the new stuff from NAPA lists for cars without ac.
Thanks!
Tommie