Search:

Type: Posts; User: old28

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    4,423

    51 Buick 263 straight 8 to PG or ? Trans

    Muley Gil

    Thanks for the reply. I have been drag racing PG for the last 30 years and have a good feel for what they will do, race ones are very efficient. You can get a TH350 chevy trans built the...
  2. Replies
    4
    Views
    4,423

    51 Buick 263 Straight 8 to PG Trans or?

    Trying to get some ideas on matching a 263 inline 8 to an automatic for an old school drag

    race car build. I don't want to spend my retirement on pricey adapters if I can avoid it.

    Open to all...
  3. Replies
    11
    Views
    4,045

    ahhh65riv Erik, Been trying to contact you...

    ahhh65riv

    Erik,
    Been trying to contact you by PM & email and my file show no messages sent. I am sure I'm doing something wrong so I'll try this, if you read this can you call me at...
  4. Replies
    11
    Views
    4,045

    Nailheadnut, Thanks, I am going to talk to...

    Nailheadnut,

    Thanks, I am going to talk to Russ in a few days about doing my heads and will pass all of these changes through him.

    Tom
  5. Replies
    11
    Views
    4,045

    Erik; The flexplate & crank adapter that...

    Erik;

    The flexplate & crank adapter that Bendtsen's sells will let me put their flexplate that has a ring gear on it like the 64-66 and will fit my '63 crank that has a 2.9 index (64-66 have a...
  6. Replies
    11
    Views
    4,045

    ahhh65riv; Thanks for the information....

    ahhh65riv;

    Thanks for the information. Bendtsen's has the flexplate to make the convertion from my 63 401 crank to 64-66 setup, nice unit but big $$$$ at $299.

    I have a rebuilt 65 starter on...
  7. Replies
    11
    Views
    4,045

    Dr Frankenbuick: Thanks for the back threads...

    Dr Frankenbuick:

    Thanks for the back threads on this matter. I can see that the only way to run the ST400 with my 63 401 crank setup is to purchase an aftermarket Flexplate with the large crank...
  8. Replies
    11
    Views
    4,045

    Flexplate exchange Question????

    Need some help, still learning this nailhead flexplate setup.

    I have a 1963 401 motor that had a dynaflow trans at one time. I want to change it over so I can run a ST400 trans. My crank has a...
  9. Replies
    0
    Views
    789

    Need a 3 groove '63 401 crank pulley

    I have a 1963 401 with a short water pump that has a 3 groove pulley and I am looking for a 3 groove crank pulley.

    This motor is going in my 29 RPU hot rod and if anyone has a 2 groove set I...
  10. Replies
    5
    Views
    908

    Ed, Thank you very much for all the...

    Ed,

    Thank you very much for all the information. I will check the code and see what I have. You guys are great. I always wanted to to build a 28-29 RPU with a nailhead in it and my time has...
  11. Replies
    5
    Views
    908

    Thanks for the information. I have little to no...

    Thanks for the information. I have little to no experience with TH400 type trans. I have used PG on all my race cars.

    The crack is from the top center and runs down towards the rear about 6". I'm...
  12. Replies
    5
    Views
    908

    Missed the pictures, hope the come through this...

    Missed the pictures, hope the come through this time.
  13. Replies
    5
    Views
    908

    Questions on Super Turbin 400 on my 401

    This is the first time that I have been on this site. I have spent the last 4 hours going over threads on 401 Nailhead motors and some on the Trans.

    To give you a little background, I just...
Results 1 to 13 of 13
TeamBuick.com Privacy Policy