OPGI has "blank" one for $ 6.00 t shipping--You ll have to fill it out yourself . ---- I bought my 67 skylark sticker from Mike Tromm at mrtromm4@gmail . Give him all the info you can on your...
Type: Posts; User: JAMES OWENS
OPGI has "blank" one for $ 6.00 t shipping--You ll have to fill it out yourself . ---- I bought my 67 skylark sticker from Mike Tromm at mrtromm4@gmail . Give him all the info you can on your...
I really didn't think Buick (GM) would go through all that trouble, for a "Special" type paint for such a small area, but you never know, so I had to ask. Thanks JIM
I had me confused for awhile, but now it all makes sense.
1967 Buick Skylark 2 dr. Can anyone tell me if the "Black" Paint on the cast metal trunk molding & body chrome molding a "special" type of paint, And if so where can I buy it. I was just...
I talked to guy from whom I bought the engine. What he told me was, that the engine was totally rebuilt sometime around 1985-86. At that time, the buick dealership did not have the correct
"Buick...
This weekend I will take some pictures -with all the Numbers / Codes. It is 100 % a Buick engine, just can't figure out why it would be grey. And --to me --It does NOT look as if its been...
I am a little confused about the engine colour of my 70 Buick 350-4bbl. All the research I ve done says it should be red, yet the whole engine is grey? This engine came out of a 70 Buick Lesabre,...
Never mind ---Found them --They are in the 1970 "Chassis Service Manual" --------"Engine Mechanical" Section ------ Division 1------Bolt Torque Specs & Adjustments
:bana: What are the torque specs / ft. lbs. for the 4 BBL Rochester Carb to the intake manifold. If memory serves me --I believe it is between 10--12 ft. lbs. Somewhere in this website there ...
:clonk:What 1967 GM "A" Body style / lines best closely resembles my 67 skylark. I need lower rear quarter panels & trunk drop filler extentions. I know they won't be a "direct" fit , but I...
Both ----Delete Membership and ALL my "Personal Infomation" as well as my ''Selling/Buying Ads"
How do I "Get off -/-Unsubscribe'' From the Team Buick website
I need to replace the "trunk filler drop panel" on my 67 skylark. ---- (this is the piece that is attached from the underside of the trunk to the lower backside of the rear qrtr).....I ve called...
Has anyone installed the Sequential light kit from Spaghetti Engineering on a 67 skylark---I just measured the Inside diameter ,and it is very small. (Approx 10 L x 2 1/4 W x 1/4 D).
Not a lot of...
While doing my '' frame off" restoration on my 67 2 door skylark, I noticed one of the previous owners plugged/ filled holes in the fuel tank--so i started looking around for the exact replacement. I...
:wavey: I am looking for the center "tri sheild emblem" ( part # 1361138) that goes on the grille of a 67 skylark. Is there a reproduction vendor that has one-Thanks JIM :thumbsup:
:clonk: Need help finding NEW brake lights (part # 5958556-#5958557) for my 2 door 67 skylark. Classicnosparts are the only one that seems to have them --but they are waaaaay too expensive. As of...
:clonk: Does anyone know if a front & rear 68-72 skylark bench seats for a 2 door or any other gm A body bench seat of the same years will fit in a 2 Door 1967 skylark. I need to know if the "bolt...
:wavey: I am putting a 1970 V8 BUICK 350-4BBL in my 2 door 67 skylark. The question I have is about the fuel pumps and gas tanks. On my original V8 300 2 BBL I had (1) one sending line with NO...
Thanks Nailhead for the pic and the info. I have a "local" lead on some cast iron exhaust manifolds from a 70 350 Lesabre for $ 150.00 bucks --I going to check them out sometime this week. Then I...
I did both
:clonk: NO GO- I ve tried hedman/sanderson/taperformance/petronix & hooker. The ones that
DO have it for the 70 BUICK 350-4BBL , would nt guarantee it will fit in a 67 frame without any problems. I...
:waving: NOT that I know of-I spoke to a tech person today and they did not mention it and I forgot to ask:thumbsup:
:wavey: I have a 1967 skylark 2 dr. It originally had a BUICK V8 300-2BBL. I removed it. Now I plan on putting in a 1970 BUICK 350-4BBL. The problem is that TA-Performance & Petronix
(doug thorley)...
:clonk:Here lies the problem--I threw away the OLD wheel cylinders NOT thinking there should be a problem. Does anyone know the reason why they have different backing plates & wheel cylinders. I...