Search:

Type: Posts; User: 38 Limo

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    414

    Rear mount bolts

    What size are the bolts in the rear mount to bellhousing? I know it's 12 tpi but 1/2" & 9/16" are this pitch. I reckon it has to be 9/16" as a 1/2" bolt has sideways slop. Could someone stick a...
  2. Dan, Clean the aerial ground under the fender...

    Dan,

    Clean the aerial ground under the fender too. Make sure you get thru to clean metal.

    Art
  3. Replies
    7
    Views
    2,253

    Good site 39cent but my lenses aren't listed...

    Good site 39cent but my lenses aren't listed there. I'm wondering if they are RHD specific. In the listing tho' they are different left to right.

    Art
  4. Replies
    7
    Views
    2,253

    Hi 39cent, You're the first reply. No there...

    Hi 39cent,

    You're the first reply. No there is no sign of L or R on any lens. I actually have 2 of the #920946 and the only difference I can see on them is after the Pat Pend message there is a 3...
  5. Replies
    7
    Views
    2,253

    1938 Headlamp assembly

    Hi,

    After 20 years apart I'm re-assembling the headlamps on my '38 and I (of course) can't remeber what goes where.:clonk: I have two lenses numbered 920946 & 920947. The reflectors are also...
  6. Thread: Need Carb help

    by 38 Limo
    Replies
    20
    Views
    3,663

    Hi Again, I still think the pipe with the...

    Hi Again,

    I still think the pipe with the stick goes to the white plastic thing but I've been thinking and the other line will go to the air cleaner for the warm air flap valve.

    Art
  7. Thread: Need Carb help

    by 38 Limo
    Replies
    20
    Views
    3,663

    Hi, The white plastic thing is the choke...

    Hi,

    The white plastic thing is the choke unloader and the pipe with the stick in it is probably the one to fit. The other pipe is probably for the distributor advance. The unloader pipe should...
  8. Replies
    5
    Views
    1,566

    gas tank float

    Tyler,

    If you put the float in a pan of hot water you will see bubbles coming out from where the leak is. You can do one of two things: 1 make the hole slightly bigger to let the gas out or l2...
  9. Replies
    2
    Views
    1,264

    Hi, The spring more than likely came from...

    Hi,

    The spring more than likely came from inside the grease nipple.

    Art :hurray:
  10. Thread: Carb Help?!?

    by 38 Limo
    Replies
    6
    Views
    1,093

    Deuce, The fuel shouldn't be that high. I...

    Deuce,

    The fuel shouldn't be that high. I think it may be a drilling hole when the carb is manufactured. See if it lines up with the feed pipe on the other side of the carb. Because they can't...
  11. Replies
    1
    Views
    680

    Scott, I've just read your post. The solenoid...

    Scott,

    I've just read your post. The solenoid has two windings inside and when you turn the key both are energized. The 'Pull-in winding' is connected between the small terminal on the solenoid...
  12. Replies
    92
    Views
    27,238

    Hi, As the name says, I've got a Canadian...

    Hi,

    As the name says, I've got a Canadian built '38 model 90 limo. I rescued it from going to the boneyard 25 years ago. It had been set on fire by vandals and the whole of the driver's area was...
  13. Tyler, One of the problems I see from your...

    Tyler,

    One of the problems I see from your diagram is that you have by-passed the start relay with your start button. The start button should go (I think) to the terminal on your relay marked...
  14. Replies
    3
    Views
    976

    David. I've just taken the flywheel off my...

    David.

    I've just taken the flywheel off my '38 with 320 engine. The bolts have a shoulder on them thais 1/2" dia. then the threads are 3/8 UNF. I've got pictures showing dimensions. If you want...
  15. Thread: Ebay Spam

    by 38 Limo
    Replies
    8
    Views
    9,839

    Sticky: Ebay Spam

    Guys

    If you get these mails don't open them. Simply forward them to spoof@ebay.com and they will handle them (I.E. go after the bad guys and shut them down).

    Art
  16. Replies
    0
    Views
    1,138

    Straight 8 big end clearances

    Can anyone out there tell me how to adjust the big end clearance on a 1938 series 90 engine. These are the babbit style bearings with shims. How can I tell if I have the correct clearance. I have the...
  17. Replies
    2
    Views
    837

    Torque Tube Seal

    Hi All,

    I asked if anyone knew where to get the seal at the gearbox end of the torque tube and got no feedback. It's the ball shaped housing and it has a big circlip inside so I assumed it's...
  18. Replies
    2
    Views
    736

    Torque Tube seal

    Newbie here,

    Is there a supllier for the seal on the ball at the gearbox end of the torque tube.

    Thanks

    38 Limo
Results 1 to 18 of 18
TeamBuick.com Privacy Policy