Bob,
Good luck on the build.
Pat
Type: Posts; User: freeman
Bob,
Good luck on the build.
Pat
Curt,
Take a look at my post, "my new 263", I had an adapter made to fit over the harmonic balancer which allowed the use of a SBC crank double pulley to drive my supercharger. It works well, I...
Thanks Jenz...
I replaced the module and battery today and after 20 minutes of programming / tuning it is running great! Very excited that only one minor issue with the supercharger belt setup and...
Me too!!
LOL
Hi Ben,
I'm using a Pertronix module in the stock distributor. The fuel injection system is made up of two Moon 97 style throttle bodies each with two Chevy fuel injectors from a small block (tuned...
More adjustments today, all was going well until the ignition module decided to die. Have to get another this week. Have a small issue with the supercharger belts, they want to slip off the...
Finally! Today was a successful day, was able to fire my engine for the first time. Had it running for about 15 minutes, made several adjustments to the fuel injection program, and was running...
Bob, this is true. I was able to get in the shop today, finished all the wiring, filled all the fluids and turned the key but unfortunately bad news, my stainless fuel lines are all leaking at the...
Getting closer but still not there, unfortunately, I've gotten busy at work and have little time in the shop, fortunately, I was able to get in the shop today and finish the exhaust. Need to re-run...
Getting closer, fuel lines complete, gas tank at the powder coater, Supercharger Blow off valve installed, more exhaust tomorrow. Had to deal with the water temperature sender today. New gauge...
Thanks Jenz.
Getting closer everyday to fire the engine, received the engine wiring harness today, worked on the blower air filter. Hoping by the end of August if everything goes right.
Pat
Thanks Suntree, first time using stainless, a little harder than steel lines, had to buy some different tools but so far am pretty happy with the results.
Pat
Thanks Long.
Had more time this weekend to start the plumbing. Just about have the engine fully plumbed, still need to finish a couple of vacuum lines, fuel lines are complete. Have to make lines...
Thanks guys.
I know 3 years, life sometimes gets in the way of projects and hobbies. I'm hoping to stay on it now that things have settled down for me. I'll post more as I progress.
Thanks
Pat
Hi All,
I've finally had time to work on my project. I have decided to try and get a running driving chassis before I start to build the body. I have been focusing on getting the motor up and...
32 Special
The valve cover looks great, put me on the list, any idea when they may be available?
Thanks
Pat
No luck so far on the manifold, I will try some other locations over the weekend.
Thanks,
Pat
Looks great! Glad to hear it's running with no issues
Pat
I think I have one, I'll look tomorrow when I'm in the shop and get back with you. Shipping will probably be pricey.
Thanks
Pat
Nice Score, Long.
I think I still have the both carbs and flapper valve under the rear carb. I can check if you're interested.
Thanks,
Pat
Your original picture looked as though the fork was not sitting correctly but the last picture of your throw out bearing shows it is. It clips into the bearing. Is this the same throw out bearing...
I believe the fork is supposed to ride in the groove of the bearing. It looks as though your fork is not riding in the groove, but, it may just be the picture.
Pat
Tom,
I purchased the adapter from Bruce Wyman, I believe his email is RBW@foothill.net
PM me if you would like the phone number, I don't want to publish the phone number without permission....
Tom,
I purchased an adapter years ago for my 263, I can't remember the gentleman's name, I believe he was from California. If I remember correctly he made adapters for the 320 also. I will try and...
Ben,
It's been crazy at work, little to no time for the project. Will be traveling for awhile so everything is on hold. Probably wont get back on the project till late fall, early winter. Not a...