Search:

Type: Posts; User: Bob

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds; generated 22 minute(s) ago.

  1. Thread: 430 Distributor

    by Bob
    Replies
    16
    Views
    397

    The capacitor mounted on the regulator and the...

    The capacitor mounted on the regulator and the coil are radio interference suppressors only. Specifications are found .5MF. on the reg. and .3MF on the coil. Specifications are found under radio...
  2. Thread: 430 Distributor

    by Bob
    Replies
    16
    Views
    397

    Sorry for the confusion, the condenser/capacitor...

    Sorry for the confusion, the condenser/capacitor being refereed to has a wire going to the points and is located under the distributor cap.

    However, if you do not have power going to the + side of...
  3. Thread: 430 Distributor

    by Bob
    Replies
    16
    Views
    397

    First checks most people do in the field is spark...

    First checks most people do in the field is spark test at the plug wire lead, hold it about 1/4" away from anything on the engine and see if you have a spark that jumps to ground. If not, you can...
  4. Replies
    7
    Views
    283

    I am well aware of the young/old aspect (: at 69...

    I am well aware of the young/old aspect (: at 69 :)

    This forum is a VB4 and while the best at one time, has been short of development and support for some time. VB4 was the most popular and...
  5. Replies
    7
    Views
    283

    It would be nice if there were someone to respond...

    It would be nice if there were someone to respond to every post quickly.

    I like forums more than "Facebook", but it seems there are more people interested in facebook these days. Originally this...
  6. Replies
    3
    Views
    364

    I think you will find that "originally" virtually...

    I think you will find that "originally" virtually no gaskets were installed at the factory with sealers. Sealers are often used to compensate for some potential deterioration in surfaces. RTV (or any...
  7. Replies
    3
    Views
    364

    More than one solution will be satisfactory. I...

    More than one solution will be satisfactory. I have never used dry gaskets.

    I am sure the Permatex Ultra Gray will do the job on the intake and the thermostat housing. It should be just fine on...
  8. Thread: Good afternoon

    by Bob
    Replies
    3
    Views
    841

    My Hollander shows the differences lie between...

    My Hollander shows the differences lie between Electra and 225. If both are Electra you may have a match.
  9. Thread: 263 Street Build

    by Bob
    Replies
    11
    Views
    3,571

    Ben, In this case we are just using a common...

    Ben,

    In this case we are just using a common replacement piston at 0.030" oversize, so cylinder walls won't be a problem.

    I am just setting up for piston valve clearances and have them to be...
  10. Thread: 263 Street Build

    by Bob
    Replies
    11
    Views
    3,571

    Anybody had the courage to do some major material...

    Anybody had the courage to do some major material removal on their heads or blocks?

    This article suggest you can take .175" off the head!

    This one says it can be done, but cautions it may be...
  11. Replies
    5
    Views
    378

    I think I would strip the primer and redo it. 170...

    I think I would strip the primer and redo it. 170 degrees is just not going to make it. Under hood temperatures on a hot day can get at least close to that. Definitely the carb heat area under the...
  12. Replies
    5
    Views
    572

    There are some alternate wiring information in...

    There are some alternate wiring information in the reference section, the link is at the top of this page.
  13. Thread: 430 engine

    by Bob
    Replies
    2
    Views
    689

    That motor will have the best exhaust manifolds...

    That motor will have the best exhaust manifolds offered on the big Buick motor.
  14. Thread: New to team buick

    by Bob
    Replies
    2
    Views
    437

    Yes, build threads are in "Projects and...

    Yes, build threads are in "Projects and Journals".

    Don't get too excited about the albums though, because we are going to do a major change to xenforo, and albums may dissappear:(
  15. Replies
    5
    Views
    572

    Glad Larry uploaded that, the one on my '66 Riv...

    Glad Larry uploaded that, the one on my '66 Riv is a little different.
    8571
  16. Replies
    5
    Views
    572

    I was messing with that about a year or so ago,...

    I was messing with that about a year or so ago, but my idle switch was working properly. Looking at the manual, it appears that the switch rolls around the linkage varying the pressure on the...
  17. Replies
    2
    Views
    392

    If the car has air conditioning, it would have...

    If the car has air conditioning, it would have been green, known as soft ray. It could have also been an option without a/c.
  18. Thread: 263 Street Build

    by Bob
    Replies
    11
    Views
    3,571

    Balanced the pistons and measured the domes. ...

    Balanced the pistons and measured the domes.

    Rotating is 558gms.

    Reciprocating is 171gms

    Domes are 9.5cc

    Piston with pin are at 525gms
    856085618562
  19. Replies
    5
    Views
    1,269

    That is an interesting number (382260), it...

    That is an interesting number (382260), it doesn't show in our reference or any other that I find. I am curious what the number of the front carburetor is?
  20. Replies
    4
    Views
    1,024

    I drive a 5800 ft summit fairly regularly with a...

    I drive a 5800 ft summit fairly regularly with a '67 GS 400. I have no problems, so I would have to say no:)

    I plan on swapping in a 455 this spring, I will let you know if it makes a...
  21. I believe they offer several options, I expect...

    I believe they offer several options, I expect this is the most convenient:
    https://fitechefi.com/products/50001/
  22. Thread: Wheel well removal

    by Bob
    Replies
    3
    Views
    556

    I had an ugly crease on a '52 which ran from the...

    I had an ugly crease on a '52 which ran from the front fender to the rear wheel opening. The inner fender needed a bunch of hammering to allow the outer fender to come out to position and take out...
  23. Replies
    1
    Views
    1,106

    You will find how to measure your back spacing...

    You will find how to measure your back spacing here:
    https://www.teambuick.com/reference/wheels_tire_howto.php

    Once you know the back spacing of the wheels that are on the car and the backspacing...
  24. Thread: cracked block

    by Bob
    Replies
    1
    Views
    1,040

    With out seeing it, it is not possible to give...

    With out seeing it, it is not possible to give accurate advise.

    I prefer either alloy spray welding or a ni-rod stick weld. Pre and post heating is what determines most of the success of the...
  25. Replies
    2
    Views
    1,146

    I think you are probably right with your steering...

    I think you are probably right with your steering wheel position.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
TeamBuick.com Privacy Policy