Search:

Greetings tried to send a private message but this system said I couldn't share my email in a private message and I don't want to post it publicly so I don't know how to contact you with these like...

I'm not talking about trains neither! Get in touch with Greg J. If ya still have the number, Thanx!

Sorry, the headers sold very quickly and I didn't see this post till today. I don't know if the person who made these is still doing them. I bought them from a guy at the Buick national swap meet in...

If you have not discovered it yet most auto parts stores carry a corrosion removing product called Evap-o-Rust nondestructive biodegradable comes in a grey plastic gallon jug with red lettering, WOW!...

Greetings Alleycat

I read in some postings that you know what mods can be done to dynaflow trans. and have done them. I have a 1955 Century that I'm using a 1956 Century...

I'm not sure I've got it. The bottom of the jack goes against the angle on the torque tube for the ebrake ? The jack hook goes up in the back of the spot where the frame members cross? I'm gonna put...

Here is a picture of the headers I bought for 248/263, actually for 1948 up with side engine mounts. They have been test run, like new, bought two sets, couldn't resist. One:waving: set is for my...

Headers?5551Kinda pretty huh? For sale. PM for price if interested. These are designed to fit around side mounts on later cars, no modifications needed .From CA, by Duttweiler, sorry about...

Looks like you are the teacher here! Look at the 1960-61 service bulletin book put out by Buick, it shows all the dynas and gives some measurements of tailshafts, might help with fabbing. Suggest...

Have dual for 56 PM FOR PRICE ETC

Buickrodder, Google that.Russ Martin Centerville Auto Repair Grass Valley CA

Nicole greetings! I think the solution to your problem starts with pictures showing your original axle(broken)and as much of the rear assembly as possible. Books such as repair manuals, don't always...

I have always understood that the lifters have a symmetrical convex curve on the bottom that is surface hardened for better(longer) wear and the lobes of the cam are not at 90 to the sides but slope...

What is the cost of this setup? serious question! Could you also build a vacuum formed clear valve cover so I can fully enjoy this view on top of my engine? kidding!<br>
<br>

I have four 320 straight 8's . three run excellantly and one is a rebuildable long block that needs a wtr jacket crack epoxied, ( for you frugal types) they weigh approximately 1000 pounds each and...

Greetings You can bore it to 425. Is it a good idea? Probably not. If you find a really knowledgeable engine builder, he will likely tell you to sonic test your block to find out how thick the...

yes eye have

Maybe you should try the phone number! Courtesy must be lost on some!

Greetings It's interesting to here all this good advice. I have 264's and yes they have cast front pulleys and so do the first 322's that came out in 1953. The cast pulleys may have a number on the...

In case I wasn't clear enough, I HAVE A PERFECT, FRESHLY RESURFACED, FLYWHEEL FOR A 264 CU IN BUICK SPECIAL Eng. 54-55 W/standard trans. If you still need one contact me. Best Regards, Greg J.

Greetings Yes only 264 flywheels/flexplate if auto are balanced correctly for this engine. Is yours not repairable? Let me know if you end up needing a replacement. I can help with the correct one....

You could just call Dave T. @ 763-427-3460 he prolly has Buick floor shift tranny's for sale that would fit by using your current trans tail shaft bolted to his older '36-'38 Spec, floor shifted...

I just took the complete changeover out of a '55 Century. Wow! That column and PS sector was so heavy I just about didn't make the 100 yards to my PU that I had to carry it. I would think that you...

Greetings I have a '65 wildcat with 308 posi, has been tested and found to spin both tires and has the lube tag still attached. Send me a private message as this carrier is an interchange for your...

Lifters first?