If it looked good and flowed good you could have some good sales for a 322 3x2 set-up with the hot rodder guys like the HAMB, second would be a good 4bbl intake. For the 401/425 I would say #1 would...
Type: Posts; User: Dan
If it looked good and flowed good you could have some good sales for a 322 3x2 set-up with the hot rodder guys like the HAMB, second would be a good 4bbl intake. For the 401/425 I would say #1 would...
ok another i.d thread........sorry
i just bought another nailhead which is either a 322 or a 264, it has no balancer, it's a 2bbl intake and the number on the deck is 16388674 (there is no "V" or...
sounds like the dampener, another way to check is to grab the belt on both sides of the crank and pull up and down (enough to rotate the motor). while doing this watch the crank bolt (or even mark...
check to make sure pcv and hose are ok. intake gasket, injector o ring are some other things....but it does sound like a vacuum leak.
I wouldn't rebuild the master yourself (or have a shop do it), Just start off with replaceing the master, clean the booster and check the 1 way valve. yes, you can blow seals out if you use the...
it's been awhile so bear with me.......i remember there are some green push in type clips that break and some white ones near the handle that are a real pain. the white ones need to be pushed...
yes, check the coolant level, if you add you need to open the bleeders BEFORE you start to fill it.....make sure the motor is cold when you do this. also look real hard at both sides of the intake...
check to make sure you have power AND ground to you taillight sockets. like said above the brake light wire does go through your turn signal switch (except the 3rd brake light it comes from the brake...
tps or maf sensor will cause it to run very poorly but most times not shut off. crank sensor will shut it down, but it also loses rpm signal (so no spark or inj pulse). cam sensor will sometimes shut...
have the charging system checked and also check the battery.
did you check the tps and maf sensors
i've used a "special" bolt i made from a head bolt with an allen head. ground down the threads so it fits in the hole, a thick washer between the puller/bolt so the puller doesn't get stuck in the...
you need to use a test light and check for power. start at the starter soleniod and work your way back. but it has a pass key, position switch on the trans, starter enable relay, and ignition switch....
i have seen more then a few that will run/start with a problem with the magnet. pull the sensor, turn motor until the magnet is visible with a light and mirror. there is 3 magnets in the insert, make...
if it's like the lesabre the cable goes bad (the plastic ends). the last one i did was a 2000 lesabre and from the dealer you get the motor/regulator combo. i don't know if you can buy the regulator...
1 more thing i forgot, if you really want to do away with the king pin/friction shock and use disc brakes. jamco WAS prototyping a B.O.P set-up a few years ago, converts it to a ball joint and disc...
yea i remember the post on the hamb........street sweeping tickets suck. i re-read your post and i think i missed the part about the starter not turning, mine would spin but not engauge the motor.
didn't ross make them awhile ago? i remember calling them for my former 263 a few years ago........this thread is getting really good keep the great info comming.
viva la hamb :)
this is a big undertaking, you need to find a frame with the same wheel base and track width (or make it work). then there's the floor issues, firewall, gas tank, steering, brake pedal,...
i would start with checking the battery cables, if it has the 2 pos cables clean them GOOD, in between both and make sure the washer goes back in the same way it came out.
no one sells what you're after, you have to make it. should've hopped-up the nailhead or gone to a bigger nailhead.
also a stovebolt is a chevrolet 6 cylinder.......:)
no torch, you can put them in a container of water and just have the loop your cutting exposed. also fatman makes dropped uprights for the buicks. also remember the shock is also you upper control...
i bought a fel pro set for my 50 super years ago at pep boys.
248: special and super
fel pro # FS 7549 B-2 full set
the super i had was sitting for at least 25 years and the guy said started...
str 8? also does it have the external arm for the sol. on the '50 i had when i first got it (and tried to start it after sitting 23 yrs) the sol didnt want to engauge, so i had to use a pry bar to...
This was a common problem with the 3.8's. sometimes the balancer will come off without a puller, then other times it won't. there is a special puller for the 3.8, you might be able to rent it from a...