Search:

Type: Posts; User: rudybdog

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    2,467

    I've got the same problem

    Iwas having problems with gears on cam and distributor haven't figured out what's causing it can't be oil happens to quick shims sounds more like what it would beif you figured it out please let me...
  2. carb

    im looking for a holley vac secdary or dubbel pumper 850or 900 ????
  3. trans & gears

    at this point there both stock the dif has posi trans 400 yes I will git a converter cam will determine with one ?
  4. Building 455 wondering what combo of parts to use

    My Block is GS Riviera (30 over) ......my heads are aluminum stage one TA performance.......ta performance headers .... carb it's 750 Edelbrock....... HEI distributor...... ...
  5. Replies
    6
    Views
    4,030

    window seals

    I got mine from ORIGINAL PARTS GROUP I wasn't vary happy with the set but it worked ok except for the door seal ends the original ones had steel in them to keep them rigged the new ones don't and...
  6. Thread: Heads

    by rudybdog
    Replies
    2
    Views
    4,981

    Heads

    Aluminum verses cast the good and bad
  7. Replies
    1
    Views
    1,160

    port & polish high flow valves

    port & polish high flow valves
  8. Replies
    4
    Views
    6,066

    I did a compression test and had no psi in #8...

    I did a compression test and had no psi in #8 cylinder I pulled the heads and found a bent exhaust valve its from earlier wen it jumped time thanks for any input Rudy
  9. Replies
    1
    Views
    1,277

    aluminum heads versus cast help need input

    Please add your feelings on this I need to rebuild my heads (bent valve )I have a 1972 GS Riviera so I thought its a good time to upgrade to aluminum heads i am looking at TA Performance stage 1...
  10. Replies
    1
    Views
    672

    the latest on my 455

    ok I did a compression test and cylinder 8 has no compression at all so I put oil in it and retested and still no compression. stuck valve ??????? :hurray::bana: and if so how to check thanks for...
  11. Replies
    4
    Views
    6,066

    oil change [bad speller]

    missing is the word after changing the oil it started missing and the brakes were stiff like I had no power(vacuum) to them I was told to things 1 shod not use synthetic oil 2 crank case psi I...
  12. Replies
    4
    Views
    6,066

    Crank case PSI

    I just switched to synthetic oil and the next day the motor started missing and my brakes acted like they didn't have vacuum and the distributed had oil in it ?? Crank case PSI ????my PCV valve is...
  13. Thread: paint

    by rudybdog
    Replies
    0
    Views
    770

    paint

    what is the proper orange for a 1972 riv 455 motor ??? color and code if possible thanks
  14. Thread: trim

    by rudybdog
    Replies
    0
    Views
    845

    trim

    looking for the trim for my 1972 riv the one that runs down the side all the way just the rubber part wood be grate I have the trim but the rubber is missing in places if not I thought I would just...
  15. Thread: Ac

    by rudybdog
    Replies
    1
    Views
    3,121

    Ac

    is there a smaller not so bulky ac unit I can use in my 72 riv thanks
  16. Replies
    1
    Views
    1,937

    blower motor

    my 1972 riv its motor stays on low to sickle air throw the car
  17. Replies
    9
    Views
    8,624

    carb

    can you tell me if I can replace the bodie of a 650 holley with a 750 using the boles & metering blocks to make 750 thanks
  18. Replies
    2
    Views
    910

    stumbols but wont fal

    thanks for the input that's about the only thing that I did not do. do you think the pump from my 650 would do the same in my750??? if you have a moment what can you tell me about...
  19. Replies
    2
    Views
    910

    stumbols but wont fall

    :finish:my 455 has a 750 edelbrock it runs grate except for off the line it wants to stumble when you give it gas if you hesitate for a spit sec its ok it total vac is 35 and i have a air fuel sensor...
  20. Replies
    1
    Views
    917

    looking for heders

    im looking for headers for my 1972 riv cant find any body how makes them help
  21. Thread: 1972 riv

    by rudybdog
    Replies
    0
    Views
    639

    1972 riv

    just finish my front end all new moog parts and every thing sand blasted and painted 2" lowering springs PS I WOULD LIKE TO THANK ALHAMBRA HIGH IN MARTINEZ CA THE SHOP TEACHER AND STODENTS FOR LETING...
  22. Replies
    1
    Views
    601

    1972 riv door wether striping

    I just got weather striping from OPG and it's s@#$t it fits around door grate but the molded ends are without a metal plate like orig this makes it real hard to keep in please dose anyone know where...
  23. Replies
    0
    Views
    520

    lowering my 1972

    cant fined lowering coil springs anyone now how makes them need front and back its for a Riviera gs if you have info on it I wood appreciate it
  24. Replies
    5
    Views
    1,325

    oil psi ok no oil to lifters

    no rocker clatter of the lifters or any thing else sines i tightened up the torque converter its just the lack of oil under the valve cover did you git a chance to look in your cover ?? i still...
  25. Replies
    5
    Views
    1,325

    oil problum

    so it sounds like i mite have a problem i will test this tomorrow and git back to you. wood you do me a faver. with a flashlight look in oil fill hole and let me know how much oil you see flowing...
Results 1 to 25 of 33
Page 1 of 2 1 2
TeamBuick.com Privacy Policy