found part #ts5760 for the rears and #ts5759 for the fronts.
Type: Posts; User: bigblackcat
found part #ts5760 for the rears and #ts5759 for the fronts.
I've dropped my 63 lesabre wagon and I need new shorter shocks. Was wondering if anybody has any suggestions on shorter shocks, or the part number of a monroe shock that is stock. That way I can...
How hard is it to replace a heater core in a 63 lesabre without A/C??? Does the fender need to come off????
Hey guys thanks for all the "Warnings", but not to sure how this topic has anything to do with my original question?
I still need some advice? I think if i can locate a stock four speed pedal,...
looking to install a hydrolic clutch set up in my 63 lesabre 2dr post. Has anyone done this set up yet and what are the pitfalls? I dont have a stock bell housing or flywheel, and dont have four...
its a tough road to lower you car if its not a chevy! I've got a 63 lesabre wagon and had the same problem. I looked at a napa coil spring catalog and checked the measurements against my stock rear...
has anybody out there used the bendtsens or eelco bellhousings? I'm looking to buy one and install it behind a 63 lesabre and do a four speed conversion to it? Pros and cons?
Needing to do a conversion on a 63 lesabre. Want to change from auto to manual shift. Was wondering if the impala pedals would bolt in, and use the z-bar and push rod from same car (63 impala?) I...
does anybody have the moog or napa pat number for rear coil springs for a lesabre or lesabre wagon. I've got a newer napa catalog but the part number is not shown. trying to cross reference the old...
looking for a low cost alternative to lower the lesabre wagon. I see that jamco suspention makes new lowering springs and shocks for about $400.00, (ouch for me) so I was wondering has any body used...
removing the complete drive line is cake; however it is a little harder to reinstalled it due to the center carrier bearing and aligning the carrier bearing bolt holes (took me 20 minutes to...
I've got a 65 st400 tranny that is having issues. I recently installed a 65 motor /tranny in my 63 lesabre. Once I got the motor started i filled the tranny with fluid. The tranny went into all gears...
I ended up marking the drive line to keep it in phase with the rear end, and pulled the whole drive line assembley. I ended up having mine shortened and installing new u-joints at that time and...
what is the length of the 65 starter nose cone versus the 63???? (i have a 65 lt code motor and 65 switch pitch tranny installed in my wagon)
I got a 65 nailhead 401 and installed it into a 63 lesabre wagon. My question is how to idenify the 65 starter compared to the 63 starter.
I've installed a 65 401 into my 63 lesabre (along with the st400 tranny) This motor has eelco valve covers on it. The problem is that the stock 63 power steering pump bracket touches the valve coves....
I wondering if anybody knows is there is a difference on a 65 riviera main altenator bracket verses a 63 lesabre altenator bracket? What I'm doing is installing a 65 lesabre 401 into my 63 lesabre...
Well I've finally got the 65 nailhead/tranny combo installed in the ol wagon. Now its time for exhaust. Thinking about running the flowmaster "hushpower II" mufflers. I've chosen these do to the...
Now that theres funny!!!!!
will 63-64 impala springs fit?
looking to drop my lesabre wagon by 2-3 inches. Looked at the suspension and found that there is a pinion angle bracket and rear panhard bar. Was wondering if anybody out there dropped there big car...
looking to install power windows in my 63 lesabre wagon. i recently found a 64 electra four door hardtop with this option. can the regulators be swapped out along with all the wiring and switches?
Very nice car Ted!!!!! So the impala clutch pedal assemblies are the same? Any exhaust manifold issues to contend with?
looking to convert my 63 lesabre wagon to a four speed or possibley a 5 speed. Looking at one of the eelco bell housings. I have a set of clutch pedals, z-bar and rods from a 63 impala. Anybody done...
okay, so is there a physical size difference between the dyna flow and st400? Would I need to modify the tranny tunnel to install a 64 tranny? Also are the splines from a dyna flow the same as the...