Search:

Thanks for the help going to strip it all down and see what i can do...Thanks again

My car got started being painted ....he was using omni acrylic basecaot clear coat he got one coat on and then he did not finish the job i had to remove several runs and wet sand out the dirt that...

I have a 350 buick engine in a 77 skylark want to pit a super charger on it only place i can find one is summitt 3500.00 antbody know where i can find on cheaper ?...THe car has a quadrajet carb can...

I have a buick 350 engine in my 77 skylark i am wanting to now where i can either get a supercharger...or a turbo kit for this or if they even make one ???...All help will be appreciated ..Thank you...

have a 76 350 buick engine anyone know the firing order and what side of the engine is my # one plug on...thank you

I have a 1976 buick 350 ...has a quadrajet carb on it...looking to get more horses..anyone know where i can find a double pumper carb? all help is appreciated. thank you:shifter:

THank you yeah was hopeing not to have to remove the engine but looks like tht is the only way to go ty again

I have a 1977 buick skylark, have a 1976 buick regal 350 that i installed in it i am having problems getting the oil pan off the car so i can replace the gasket i can get a gasket on it but really...

I have a 350 buick engine 1976 i need a crankshaft pulley a 3 groove water pump pulley and a 2 groove alternator pulley, i have checked poston, jegs and summit no one can help me any ideas where i...

car is over heating bubbling up in my reservoir replaced thermostast and changed out my head gaskets car is still doing tthe same thing ....think i have a crack in one of my heads or could it be...

Have to remove my cylinder heads and am going to replace my head gaskets when i put them back on ...can you please help me with the correct torquing for this?have a 1976 buick 350...thank you

Looking to upgrade my 77 skylark to a lower gear and a posi trac rear end has a 2.53 gear with a 26 spline 8.5 10 bolt anyone know how this might be done... or what rear end i can switch mine out...

Have a 77 skylark went to replace my gears measured out as a 8.5 10 bolt
running 2.56 gears was trying to update to a 3.73 posi trac but have a 26 spline and can not find this combination...

Thank you for your input, got my scoop this weekend saw in hand ready to get started ....once again thanks. :rod:

Getting ready to cut the hood on my car to install a hood scoop, any suggestions on what tool would be the best for this job? :thumbsup:

I JACKED MY CAR UP TURNED DRIVESHAFT 1 AND A HALF TURNS TO MAKE WHEEL GO AROUND ONE COMPLETE TURN I DIVIDE THIS BY 2 COME UP WITH .075???? STILL NOT SURE HOW I AM GEARED..?:repost: ..:angry:

yea....put a 350 in this car came with a 6 cy and trying to find out how the rear end is geared

OK found #. for the rear end 555771 anyone????? know these #'s and tell me how my car is geared and what i would probably need to replace them with for more speed better performance....i do...

beckley west virginia....gas price 2.25

k..k..thinking about going with a cam and heads if anyone knows what #'s i would need for this and what i would have to do to my engine if anything to suport this and not burn it up i would...

I have a buick skylark 1977 with a 350 engine quadfour quadrajet 4 bbl carb?

looking to get horse power and better performance thought about nos , cam, and bettr rear end gears any suggestions and...

the tach has 4 wires the red goes to a 12 volt +
the black is the ground
the yellow the + side of the battery
but the green is suppose to go to my tach source saids such as a tacho terminal...

:shifter: I NEED TO KNOW WHERE THE TACHOMETER SIGNAL SOURCE ON MY DISTRIBUTOR IS AT I HAVE A 350 BUICK ENGINE IF ANYONE COULD HELP ME PLEASE

happy newyears all!.......christmas and new years has came and gone, ever one wish real hard for spring so we can bring our metal babies out from the garages and maybe it won't seem too...

do you know any where or anyone that has a 200r 4 speed or manual tranny that would fit this car and engine?