Search:

I purchased mine thru them most worked fine they don't have sealed nuts I used rope caulk To do you know how the rear seals goes for the tunk
does it glue to inner lip so seal faces out or outer...

Do any one know which direction the trunk seal goes? this seal goes in the grove of the body at trunk opening. Does it get glued to the bottom and inner lip so the seal faces out or does it get glued...

Does any one know who can repair Right j-bar on my rear bumper or does anyone know where I could buy one?????
1956 Buick Special with dual factory exhaust right side jbar for rear bumper

does anyone know if the back glass is reprduced for a 1956 buick special 2door hardtop model 46R style 4437? I would like to repalce mine so I will have all new glass. the car is almost ready for a...

on my 56 I installed it on the fire wall . I removed the bubbles and redirected the drain system. I am using a corvette style master !" bore 7" dual Booster with 4 wheel disc brakes . All works fine...

I had a set made by Detroit Spring ,3" lower than standard works great, they coast about $50.00 per spring .You still have a great ride

is that a brass or copper float or man made material ?the man made material soaks up the fuel and sinks. Causing flooding. Put the float in some gas and leave it over nite se if it is floating or...

there is a vacuum diagram in this data base if you can't find it let me know i will try and find it again. I hope this helps:shifter:

tanks inc in Mn. all you need to do is measure your fill tube location. Also get a new sending unit for your fuel gauge from them they are about 1/2 the price of orginal:shifter:

also try forida fastner:waving:

this is a problem mine is bad also I connected the dash lite wire to connection for the head lite feed. they work in low beam and high I hope this helps:laugh_4:

I to use valvoline have had no wear at all. When i overhauled my engine cam and lifter were replaced. Comp cam also makes a oil additive that works fine all of my freinds with flat tappet cams are...

try classic fab. or bills he has a lot of sheet metal for buicks

what does this mean when you try and post something and it will not let you saying token expried?????:clonk:

thank you!! for delete one of them I still have 2 I will check to see if I can delete the other 1

1956 322 255 hp engine can I install a dist. out of a 401 engine? if so what needs to be changed?:clonk:

how do you delete an add completely. when I just submitted an add it told me not areas were completed but the add posted. I submitted another add it was also posted now I have 2 add for one trans...

thanks I found a 1986 chev pickup neutral switch will work. I pick one up today I made bracket for shift tub to drive the switch. Next I need to find someone that can make a lens for the trans shift...

Has any one changed trans from dynaflow to a 700R4 and used the factory steering column. If so what do you need to change other than neutral safety switch? :car:

Tanks Inc. sells what you what for $200.00 just measure your fill location and they have the right tank fill neck and rubber connector come with the tank also if you need a new sender they have it...

Newport Engineering makes the conversion very simple remove vac. motor and bolt in newports electric motor they furnish switch and some wire aswell. I used my vacumn switch knoband location, so it...

eelco product are not the best!!!! I used one of there valley covers on my 322 had to gring down excess aluminum on both sides so it clwared heads also is about 1/4" to short. Phoenix transmission...

check with PRC they made mine for my 1956 Hope this helps:shifter:

I have found 1" sway for a 1958 thru 1964 Chev Impala is almost a bolt in width is 1/2" less other wise is the same.:hurray:

FYI I just recieved a 1" front sway for for a 1958 thru 1964 Chev Impala this will fit 1956 Buick Special with little to no modifications. I have looked high and low for a front sway bar No one...