Search:

Type: Posts; User: ss-truck

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,562

    I have used that before and worked real good ....

    I have used that before and worked real good . The ball point paint pen was great for getting in the tight areas with precision .
  2. Thread: 71 GS emblems

    by ss-truck
    Replies
    3
    Views
    970

    I did not use the nuts on mine , instead I used...

    I did not use the nuts on mine , instead I used the barrel clips , so all I had to do was just push the emblem into the holes .
  3. Thread: 71 GS emblems

    by ss-truck
    Replies
    3
    Views
    970

    This should help you on emblem placement :...

    This should help you on emblem placement :
    http://www.buickperformance.com/emblems.htm
  4. Replies
    4
    Views
    1,681

    Make sure you use vacuum gage to check seal . A...

    Make sure you use vacuum gage to check seal . A bit off subject , my son and I built an LT-1 for his Camaro and the intake would not seal on lower side . tried 3 different type intake gaskets and NO...
  5. Replies
    4
    Views
    1,681

    The valley pan is very easy , just push it down...

    The valley pan is very easy , just push it down into the valley and there will be four tabs that lock under the edge of the cylinder head to hold it in place . I would use a sealer like Copper Coat...
  6. Replies
    8
    Views
    1,870

    On a completely stock motor 4.10 is far too much...

    On a completely stock motor 4.10 is far too much gear and 3.73 would be questionable . Probably a 3.42 would be a good choice with the stock engine . Are you planning any engine mods , if so you...
  7. As in the previous post heating is probably your...

    As in the previous post heating is probably your best option . When you heat have a candle ready and after you get the housing hot melt some of the candle wax into the bolt hole . Also be very...
  8. Thanks for the info . And customers can't...

    Thanks for the info . And customers can't understand why it costs so much just to spot in a small area , much less an all over paint job . A while back I did a Lincoln repair on left quarter , slight...
  9. Replies
    17
    Views
    2,674

    Recently built modded motor for my son's Z/28 and...

    Recently built modded motor for my son's Z/28 and machine shop told us NOT to use synthetic oil for initial crank up and next oil change . Only after very thorough break in could we use synthetic ....
  10. Replies
    3
    Views
    3,013

    On our car we have 235/60-15 on the front and...

    On our car we have 235/60-15 on the front and 275/60-15 on the back , 295/50-15 will fit the back .
  11. Thread: Ebay Spam

    by ss-truck
    Replies
    8
    Views
    9,839

    Sticky: I got a notice a few days ago that a foreign...

    I got a notice a few days ago that a foreign contact had tried to use my pay-pal account . They needed me to refresh my account and to do that I needed to enter all my info .NOT . It all looked and...
  12. Replies
    15
    Views
    5,774

    Poll: Jared came from Rad Rides by Troy and went back...

    Jared came from Rad Rides by Troy and went back to them . I guess he got a better offer .
  13. I had a similiar situation with a 98 Cadillac and...

    I had a similiar situation with a 98 Cadillac and changed the hub assembly and the noise went away . Not to say that will fix your problem , but it got mine . The hub assembly is a little pricey .
  14. Replies
    2
    Views
    631

    The 455 definately has its advantages ,but don't...

    The 455 definately has its advantages ,but don't let the 350 fool you because it is smaller . i have one in a 71 Skylark that has run 11.92 in 1/4 . It is a very streetable motor and will run on...
  15. Replies
    7
    Views
    1,500

    I cheated on mine and have a 12 bolt . I am using...

    I cheated on mine and have a 12 bolt . I am using Moser axles and retainers , Strange gears . the posi is filled with Eaton parts , carbon fiber clutches , 800 lb springs . Moser cross shaft and...
  16. Thread: Fuse Box

    by ss-truck
    Replies
    14
    Views
    2,297

    fuse box

    Before you get too upset , Lectric Limited has a replacement box , about $60 . A couple of hours to put it in , where are you located , if not toooo far I will install it for you . But from the way...
  17. Can't make it this year , car not ready and will...

    Can't make it this year , car not ready and will be recovering from upcoming surgery.
  18. Replies
    39
    Views
    12,895

    I have two Pertronix units and love both of them....

    I have two Pertronix units and love both of them. One is in 350 Skylark street car ( 11.90s in quarter) the other in GSX show car. Never any problems , run great and start good hot or cold. IF I do...
  19. Replies
    2
    Views
    1,002

    I have the XM and am very happy with it. Yes it...

    I have the XM and am very happy with it. Yes it can be piped into the computer, I use that a lot. Just plug in my headphones and work away. XM also covers Nascar if you are interested. You mentioned...
Results 1 to 19 of 19
TeamBuick.com Privacy Policy