Search:

Type: Posts; User: Jenz38

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds; generated 21 minute(s) ago.

  1. Thread: My New 263

    by Jenz38
    Replies
    42
    Views
    6,516

    Nice to hear,that it runs....😀🤘🏼

    Nice to hear,that it runs....😀🤘🏼
  2. Good Job.. 😉👍🏼

    Good Job.. 😉👍🏼
  3. This one ..,i had use it in my old 248 from '48...

    This one ..,i had use it in my old 248 from '48 and now in my 263 too.. ,and it works perfect ....
  4. Thread: My New 263

    by Jenz38
    Replies
    42
    Views
    6,516

    Nice to see thats it goes on.... Absolutley...

    Nice to see thats it goes on....
    Absolutley awesome your bend- job.
    I'm courios about the running engine :thumbsup:
  5. Replies
    58
    Views
    4,542

    ...nice Thread..:D

    ...nice Thread..:D
  6. Replies
    3
    Views
    676

    The Kits are comes complete ..(not like some...

    The Kits are comes complete ..(not like some modern Cars ,like a Hummer H2,there're no Headgaskets inside the Engine-Gasket-Kit ) .
    I had ordered me extra a two Piece Rubber Gasket for the rear...
  7. Replies
    654
    Views
    206,204

    Yes Guys... very nice to see that something...

    Yes Guys...
    very nice to see that something goin' on in this thread..:thumbsup:
  8. Replies
    9
    Views
    591

    You have tryed fresh gasoline ?....maybe the old...

    You have tryed fresh gasoline ?....maybe the old one in the gastank has lost the ignitability..
  9. Replies
    0
    Views
    261

    '37-'38 special ,mc "interchange"

    I had try to let sleeved my mc,but the machining shops told me, it isn't possible at this part.They can overbored it and build a new Piston for it.
    That wasn't ok for me.
    The Remanufactured mc ,I...
  10. Thread: "hopped up" 263

    by Jenz38
    Replies
    11
    Views
    1,871

    Ben, any news ?

    Ben,
    any news ?
  11. Yes,you're right, Dave ...:)

    Yes,you're right, Dave ...:)
  12. Dave, If I understand you right..yes, of course,...

    Dave, If I understand you right..yes, of course, i drive with a clearance (best results with .10) with my solids.
    But for finding the problem at ( Joe's) hydraulics, I would try it with zero lash...
  13. Replies
    35
    Views
    5,039

    👍........😉

    👍........😉
  14. Yes, Correct.. In my case ,i never use a vacuum...

    Yes, Correct..
    In my case ,i never use a vacuum gauge...😉..more than closed valves ,new Pistonrings, a sealed intake and a correct timing (chain)isn't possible.
    The less pressure/vacuum, I would...
  15. In fact I drive my 263 with solids, but I would...

    In fact I drive my 263 with solids, but I would give the hydraulics zero lash at running engine,check it by your ears, (then you're can be sure that the Valves are completely closed) .
    I do it on...
  16. Replies
    35
    Views
    5,039

    Your choke flapper ok ? ...may be it sucks to...

    Your choke flapper ok ? ...may be it sucks to closed position under airflow runs throu the carb intake ?
  17. Replies
    18
    Views
    4,225

    Yes ,now it works ...👍 If Interessented,here's...

    Yes ,now it works ...👍
    If Interessented,here's my set up:

    http://up.picr.de/21539170rr.jpg
  18. Replies
    18
    Views
    4,225

    I can't see the pic,only many many other...

    I can't see the pic,only many many other things...😆

    If do you wanna use a single tube exhaust you need minimum the Diameter of the Manifold outlets...
    Me drive with a dual tube exhaust and it...
  19. Looks more like Packard ...

    Looks more like Packard ...
  20. Thread: 263 rebuild

    by Jenz38
    Replies
    79
    Views
    24,110

    👍....sounds good..😉

    👍....sounds good..😉
  21. Thread: 263 rebuild

    by Jenz38
    Replies
    79
    Views
    24,110

    Yes ..., I will try a high quality 20 W 50 at...

    Yes ..., I will try a high quality 20 W 50 at next also , my engine runs for me a little bit too loud/rough at 180° Oiltemperature on the road in the constant 3000 revs.
  22. Thread: 263 rebuild

    by Jenz38
    Replies
    79
    Views
    24,110

    Ok, i had pimped my pump carefully a little and...

    Ok, i had pimped my pump carefully
    a little and have modified my block for a full float system with a PH 8 A spin on Filter .., have same pressure like yours 😉 whatta Oil you drive ? I use a 10 W...
  23. Thread: 263 rebuild

    by Jenz38
    Replies
    79
    Views
    24,110

    Yes ..👍,nice to hear that and it looks C👀l... ...

    Yes ..👍,nice to hear that and it looks C👀l...
    How much Oilpressure do you have ? ...and you drive a fullfloat Oilfilter ? ...if i remember right , no ? ... or is yours on the pic a 262 (?) Chevy...
  24. Replies
    654
    Views
    206,204

    .....'wish you there good luck ...💪👍

    .....'wish you there good luck ...💪👍
  25. Replies
    4
    Views
    1,435

    The 263 and 248 use the same cover ...theyre both...

    The 263 and 248 use the same cover ...theyre both with a "modern" seal gasket not with a rope ...(i can only tell it from '38 up ;-) ).

    M2C
Results 1 to 25 of 311
Page 1 of 13 1 2 3 4
TeamBuick.com Privacy Policy