Search:

Type: Posts; User: lakester

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,861

    41 exhaust manifolds

    This shouldn't be a problem as I have a Edmunds 2 carb intake manifold
  2. Replies
    2
    Views
    1,861

    '41 exhaust manifolds

    Can two front exhaust manifolds be used to eliminate the reverse bend uf the exit of the rear stock manifold?
  3. Replies
    18
    Views
    4,225

    dual exhaust

    If you need dual exhaust to run dual carbs howcome Buick used only single exhaust on their '41 cars with dual carbs?
  4. Replies
    41
    Views
    6,311

    I've used 00 welding cable for leads. Use a...

    I've used 00 welding cable for leads. Use a 12Volt jumper battery. That will wake up your starter. Don't grind it too long.
  5. Thread: 243 intakes

    by lakester
    Replies
    7
    Views
    1,836

    41 dual carb

    I have a 41 dual carb manifold for special/super engine. NO exhaust manifold.
  6. Replies
    12
    Views
    2,928

    320 parts

    Stock 320 parts are available from a number of Antique Buick Parts Dealers. Check in Hemmings Motor News. Used speed equipment is nearly impossible to find. Several people can grind you a cam and...
  7. Replies
    11
    Views
    4,708

    1934 Series 40 all came with the small st eight,...

    1934 Series 40 all came with the small st eight, This engine was new for 34 and became the basis for all small Buick eights.
    The 320 roadmaster engine came out in 1936 and was perity much unchanged...
  8. Replies
    11
    Views
    4,708

    Are you talking about a 1948 Four door or a 1934...

    Are you talking about a 1948 Four door or a 1934 model 48
  9. Replies
    233
    Views
    32,628

    Also the class displacement limit for Bonneville...

    Also the class displacement limit for Bonneville is 325 Cu. in. so 263 is a little small even with an 1/8 "bore.
  10. Replies
    1
    Views
    1,442

    Pontiac distributor

    Can anyone tell me the modifications necessary to install an Pontiac HEI distributor in a 248" st 8 Buick.
  11. Replies
    33
    Views
    5,387

    I would think twice about using high detergent...

    I would think twice about using high detergent oil.I would stick with straight viscosity Non Detergent oil.
  12. 2X2 manifolds were only available in 1941 & 42....

    2X2 manifolds were only available in 1941 & 42. Fourbarel carb came only on 1952 Roadmaster
  13. Replies
    3
    Views
    790

    Several ads in Hemmings Motor News For shock...

    Several ads in Hemmings Motor News For shock rebuilders.
  14. Center section should be available from several...

    Center section should be available from several dealers listed in Hemmings Motor News.
  15. Replies
    0
    Views
    857

    McMeekin's Brs Bonneville Coupe

    Good article in latest issue of Bonneville Racing News on McMeekin Brothers
    Nissian Coupe powered by 325 Cu.in St eight. Ran 170 MPH in Aug.
  16. Replies
    11
    Views
    2,651

    Roadmaster center exhaust manifold sections were...

    Roadmaster center exhaust manifold sections were being reproduce. WShould be available from any antique Buick dealer. Check in Hemmings Motor News.
  17. I believe they are the same. The 320 bellhousing...

    I believe they are the same. The 320 bellhousing is different as are the standard shift transmissions.
  18. Replies
    5
    Views
    984

    I believe Pilot bushing in Dynaflow crankshaft is...

    I believe Pilot bushing in Dynaflow crankshaft is latger than one for std shift.
    Have to make bushing if this is true.
  19. Replies
    5
    Views
    984

    There is no subsitute for cubic inches.

    There is no subsitute for cubic inches.
  20. Replies
    654
    Views
    206,204

    263 Buick used torque tube transmission,late GM...

    263 Buick used torque tube transmission,late GM rear end is open driveline.How are you connecting the two?
  21. Replies
    32
    Views
    6,095

    That engine stock should have enough torque to...

    That engine stock should have enough torque to pull stumps. I would lower the compression or put in a stock cam. Not what you want for a race car but will shurely help the torque.
  22. Replies
    4
    Views
    984

    I have a 34 Model 40 3 windowm coupe. Will look...

    I have a 34 Model 40 3 windowm coupe. Will look for may manual.
  23. Replies
    2
    Views
    1,342

    Sm or lg engine?

    Sm or lg engine?
  24. Replies
    9
    Views
    3,683

    Gently tap the switch. There is a metalized cork...

    Gently tap the switch. There is a metalized cork ball in there which can get hung up. It this works then disassemble and clean tube.
  25. Replies
    5
    Views
    1,525

    I think that a 51 super will have insert bearings...

    I think that a 51 super will have insert bearings on rods and mains. I would think your 6 cylinder is probably a 272 or even 228cu.in. engine. It won't bolt to a Buick trans.
Results 1 to 25 of 37
Page 1 of 2 1 2
TeamBuick.com Privacy Policy