That is very cool to hear. I wish Arizona was closer to Florida....
Scott
Type: Posts; User: scott kerns
That is very cool to hear. I wish Arizona was closer to Florida....
Scott
If the car is a skylark GS it will be much more rare than the regular skylark. The fact that it has bucket seats and a console makes it more rare than the standard bench seat and column shifter.
...
Hey Butch if you could send me pictures it would be appreciated. Please send them to kernsscott@bellsouth.net.
Thanks.
Hey Butch if you could send me pictures it would be appreciated. Please send them to kernsscott@bellsouth.net.
Thanks.
Hey would you take pictures and post them if possible? If RacnJsn95 doesn't want it I may. Is this an AC car?
Scott
Hey guys i have a console with a few cracks and piece that is broken on the base. How do I go about repairing and refinishing this? Do I use bondo?
Thanks
Scott
Are you trying to remove the switch or lock cylinder? If thelock cylinder, insert a paper clip in the hole that is underneath the hole for the key, push the paper clip in while turning your key and...
Mine is a 350 buick and read a couple of threads re: the jetting and CFM increase when installing a carb from a 455 and was wondering if this would be a good choice. Also wondered where I could buy...
Has anyone run into the problem (if you haven't I'm not sure you have an old car) of rust in the gas tank? Noticed the rust when I installed a new fuel filter with an external glass case. Has anyone...
What is the best quadrajet and why? I plan to rebuild one, or give it a good college try, and before I put considerable time and effort into it I would like to know what the group thinks.
Thanks,...
Well I made the repair. Time will tell, but if it lasts a while longer I'll be happy.
Thanks for the help.
Scott
Thanks will give it a go!
is this the same solder as that used in sweating pipes in your house?
Hey folks I noticed a small crack in the radiator of my car after a good warm up. It is located where the upper radiator hose enters the radiator. Is there an easy and durable way to repair this...
I have been working on getting my car to stop successfully, and now it is time to turn my attention to making it go. Long story short, the car starts easily and runs smoothly once warmed up and at...
My wife bought me this instrument cluster (see picture) and she said the ebay add said it was out of a 67 gs. It has a user defined sped warning speedometer. Can anyone confirm make and model this...
was there a reason for the earlier heads to crack? overheating?
Any way to stop this from happening?
So I bough this console to fit my 66 skylark. It is from a 67 Wildcat. Great deal, great console, but having seen tachometers on ebay selling for $400 I'm in need of help finding an aftermarket tach...
Ok so the numbers on the axle tubes didn't help me identify my gear ratio. As a result, i cracked the differential open to drain the fluid and get the numbers on the ring gear. Here is what i found...
yes I have seen the manual and I still can't figure it out. I was wondering if it was a bad stamp job and it was supposed to be an "OB" .instead of a CB
Well i'm trying to identify the rear end in my 66 buick skylark and i can't make heads or tails of the numbers i've gathered. Here they are......
3875744N CB1101 W Wasn't sure if the "C "was a...
In my first 66 Skylark, my first car, it came with a 300 ci engine and 2 speed powerglide trans. Well at the time, mid 80's, I had a 350 olds engine fall into my lap and I built that for my buick...
Well the brakes fit...I was introduced to the lost art of Re-arcing the brakes....onto the front brakes...
Just checking to see what parts (if any) are left. If you have the oil pump how much will you take for it?
SCOTT
The seller did not advertise a rear end change, and if he had i wish he had sprung for posi. The information gleaned from the rear doesn't correspond to the manual. The information was taken from the...