Yes it will bolt to the water pump. Don't know if the back spacing will work or not....
Type: Posts; User: USMC4LIFE
Yes it will bolt to the water pump. Don't know if the back spacing will work or not....
I have a 364 in my 32. I can email you the part numbers of the hoses I used. The upper was an upper hose from a Chevy 1500 and the lower was a lower hose for a F150. I had to trim both hoses and...
Anyone have a lead on where I can find the molding clips for the front fender and front/rear door trim for a 61 LeSabre? They need to be narrow enough to fit inside the trim channel.
Clip on the...
Tom, I pulled the transmission last night. The notches in the torque converter hub are .500 deep. I also measured the tabs on the oil pump gear. They measure .500 (deep) as well. If I pull my...
Tom, thank you for the reply. Like I said most of the forums I read were generic to TH350/TH400 and quoted a maximum of 3/16 and minimum of 1/8. We all know that Buick is a breed of its own and...
I just finished mating a 66 ST400 to a 1961 364. I have the correct flexplate and crank bushing installed on the nailhead and torqued correctly. After I got the matched set put in the car, I...
I just finished mating a 66 ST400 to a 1961 364. I have the correct flexplate and crank bushing installed on the nailhead and torqued correctly. After I got the matched set put in the car, I...
Had the same issue with my 364. After realizing that fram filters really restrict oil flow and researching engine oils this is what I found. WIX pn 51049 flows way more oil and Rotella 15-40 has...
HELP!! I am trying to find little clips that hold the chrome trim to the front fenders of a 61 LeSabre. I would like to get a part number or contact information to someone who might have them. I...
Hello. I was wondering if anyone might know what other hood from 61 buick models will fit on the lesabre. I found a couple from the Buick special. Will it fit?
Does anyone know where I can find front and rear quarter panels for a 61 4Dr hardtop? I also need the piece where the rockers roll up into the wheelwell. Any help would be greatly appreciated....
Thanks for the help. Does your manual also have what hood hinges interchange?
I have a 61 LeSabre 4-Door Hard Top. What other models of the 1961 Buick have a hood that will interchange with LeSabre? I am currently looking for one, so if any of my Buick brother know where one...
Sorry, just sold both of them on ebay. I will keep my eye open for another. I got your message late because someone smothered me with a wet blanket.....
I have a couple 364 4bbl intakes. Casting number 1173313. Please let me know if you are interested. I will sell them outright, if not they are going on ebay the first of December. ...
A regular intake. Stock is fine. I am looking to run an square bore carb on a stock 364.
I am looking for a 4bbl intake for a 57-61 Buick 364. I understand that they are kind of scarce, however I am not going to sell my childrens plasma and bone marrow to purchase one. If you have one...
Great info. A little late now, but thanks for the word.:shield:
I used that gasket that was circled. From what I have been told by some hard core old timers, the one he had in there is for the dumpers on a 3x2 set up. Runs great now. Finally after 11 years, I...
Thats what i thought. I replaced that gasket today. Back to 21 inches of vacuum and runs like a new car. Thanks for the response.
Bought a rebuilt Rochester 2bbl for a 62 Buick LeSabre with 401. When I put the carb on to dial it in, I noticed that the engine went from 21 inch of vacuum down to 16 inches of vacuum. I sprayed...
THIS IS A BUICK FORUM!!! If you really want to fix it, go rent a cherry picker. Hook the picker to the radiator cap, and lift. Once the cap comes off, drive a Buick under the cap. Lower the cap. ...
Got it all put in and I am now driving it. The mount works great. Goes to show that a little bit of common sense and an electric drill, most anything will work. 91 Jeep Wrangler transmision mount...
Make sure that flap in your passanger side exhaust manifold is not stuck partially closed. It will cause the exhaust to push back up through the intake (as designed for a cold engine), making the...
Timing is to far advanced.