Search results

Pomona Swap Meet | Event Hours & Dates| Pomona Swap Meet

I purchased a letter "I" on ebay with excellent chrome. I was too lazy to measure my old letter on my 63 skylark because it looked so alike. I receive it and the mounting studs are 1/2 " seperation center to center. My "I" on the hood of the skylark are 5/8" separation center to center. Another...

GL03 submitted a new listing: retainer seals for stainless trim molding on doors, fenders and quarter panel - retainer seals for stainless trim molding on doors, fenders and quarter panel View the entire listing here...

my tails have lost the shape from multiple repairs. Currently repairing from recent collision. Can anyone give me a pic with measurements of the tail for example the width of the corner bend, the distance to the side hockey puck to the bend. If too confusing just a image with ruler placed over...

Upon shopping for parts for the 63 Buick skylark, I was disappointed by the popularity of wrong parts that are available for this car. Ultimately, I as a consumer get less, and the seller makes a profit. The aftermarket manufacturers of urethane and polyurethane sway bar bushings do not cater to...

Symptom: transition from idle to part throttle hesitation under load and stalling under snap of throttle Checked and verified 63 Service manual specs 215V8:Timing set 5 degrees, no vacuum advance, plugged line from aluminum base of 4gc rochester. Tach 500 rpms for automatic. Vacuum line from...

https://www.pomonaswapmeet.com/event-info/car-show-hours-dates/

GL03 submitted a new listing: 63 special/skylark Upper control arm stops - 63 special/skylark Upper control arm stops View the entire listing here...

I made this cheat sheet for selecting jets and idle mixtures with a four-gas analyzer. The source article I got it from is out there if someone wants to look for it. I think the author deserves credit, but I can't recall his name. The red vertical line14.3:1 is the recommending mixture for...

Does anyone know where this exhaust port goes to on engine with Rochester 4GC? The 2GC has a connection. The service manual does not have this information. I can see on the 2GC the tube secures on the valve cover leading up to the top. There is vacuum here at exhaust port, and changes idle...

Problem: The 63 buick special/skylark y-pipe may get bent right under the crossing under the transmission pan if the vehicle bottoms out. The crossing pipe in bent state is too close to the pan transferring heat into the transmission. Also, the typical exhaust tubing is bent with warped shape...

It has been challenging to finding shocks on the 63 skylark, along the way I have installed incorrect shocks and not much options to choose from. The vintage car market for parts has moved up to inflated prices including J-nuts for qty of 4 to $225. + $9. shipping on ebay. I decided to increase...

On ebay i'm seeing parts flipping. Easy to tell, the seller has little knowledge of the part and asking for a high price way beyond inflation consideration. Another type of part is a listing with least specs provided, yet it specifys fits your car, it does not. The most common part I see is...

The Gabriel part listing for rear shocks on 61-63 buick special/skylark is 81495, it has the upper mounting S1, lower mount EB1, this is incorrect for the upper mount and the extended length of ~20 in. This mistake has been for more than 20 years. The correct mounting is ES9(.44" hole) or...

GL03 submitted a new listing: New Rochester 4GC accelerator pump - New Rochester 4GC accelerator pump View the entire listing here...

It is a challenge to find replacement parts specially if obsolete. I put together some pics, because we like them more than reading. A flasher on a 60s buick may have this recommended AP273S in 63 with a bimetal design, thermo circuit breaker. We can see how we end up with this #552 more...

I'm wondering tire stem valve that is being used on 60s rims. The T413, 414, are all various lengths for .453" rim hole. I'm measuring a .425" rim hole on a 13 in. OEM GM rim from 1963. The new T413 valve stem is actually bigger at .478" with the .453" rim hole specification. About a .030" for...

Can anyone provide pics on their single to dual master cylinder conversion? I'm looking to see clearance at the frame and what was done about the brake lamp switch. Possibly, if someone can describe pedal feel before and after conversion. Size of piston, etc.

GL03 submitted a new listing: 1963 buick skylark pedal pad with manual brakes - 1963 buick skylark pedal pad with manual brakes View the entire listing here...

GL03 submitted a new listing: 1963 buick skylark brake pedal pad - 1963 buick skylark brake pedal pad View the entire listing here...