Search results

Guess nobody knows, Well just thought somebody might of had this info and save me a lil grief. So when I fig it out, will post and save someone some time.Thanks,Knuck:clonk:

Heres my question, who knows how many and what size clips it takes to replace the trim side pieces on a 56 buick special 2 door ?????? mine was all broke when the pieces came off. So was wondering if ANYONE might have this piece of info. I don't think Im the only one who's done this. Appered to...

howdy fellas, :wavey:I know I been busy doin chrome work and trying to get parts. Speaking of parts,check these guys out. TONS of NOS.For just about anything,just a place I fell into while diggin on the web. http://www.midwestnos.com Now I gotta go to work, just never ends. ya'll take it easy.Me...

What I need to know is, what is a good,fair price for boiling out a radiator??? I'm sure there has to be a few of you do it yourselfers that have got this done. Thanks Knuck

not sure if this is the right spot, yet lookin for a set of coil springs for the front and rear for rosie. 56'buick special 46r. any leads would be helpfull. along with any ideas concerning this issue.ie, shocks???what good ones are out there for the front. rear.air shocks?? don't knownot...

well thanks to you all:beers: gave me a few more good places to look at for networking for parts. slowly chipping away at this lil project till snow flys. so trying to tie up a few loose ends. for the 6 month hibernation:D cuz by then i got my harley motor on my kitchen table for a...

well got the undercarrage and the frame por'ed along with the engine compartment and the wheel wells. good thing I used a cheep gun, cuz it aint worth squat now:confused: also got the upper and lower control arms done. along with the springs. motors getting rebuilt as we speak. tranny will be...

looked even at C.A.R.S. inc. and surprizingly did not find it there. looking for the gasket that goes tween the front spindle and backing plate. :confused: any info would be usefull. havent stoped at napa yet, think they would have something like that for a 56 buick special?? or can it be cross...

being a biker for about 30 years we got a saying in our subculture (what comes around, goes around) I believe that may be some of the problems we have on this planet. most everyone wants to make a unrealistic profet for what little is done. now I'm not saying whats fair is fair. but realy, have...

very simple poll. just state what the gas price is in your area, and in what city/state. here in St.Paul, Minnesota. gas is $2.69.9 for reg unleaded.

parts car. hey dude. I got a parts car and live in st.paul. maybe we can work out a swap of some kind. email me

my understanding is that the stuff( I got the por tank seal kit) don't work in a contamanated tank. so first question is, did ya boil out your tank first?? second one is, if it pealed back with air. sounds like ya might have to start from scratch. the question I have with the stuff is. will that...

got them sandblasted. got por15 and metal mask. heard tell it's best to heat up the manifolds to get excess liquid residues out from the pits of the metal. quite sure this is the way to go,:thumbsup: yet before I fire up taters amana. any one know about what temp would be the best to complete...

been watchin this thing here and it's gettin PLENTY of action. the first I have ever seen . started at 10 bucks. up to 349 bucks now and still got 5 days to go. must be a VERY oddball piece of automobile history. BTW I have been lookin for them side trim pieces that go on the back edges of my...

if your looking for SS parts or misc parts. think I could help ya out. see, I got a parts car. so dont be shy. I got what I needed. BTW I am in need of the lil ceramic do dads that sit on the fire wall.I don't even know what the heck they are???? any help? are they integreal?? got 2 56's and the...

Rivman heres the thing. its a 56 buick special.2 door. model 46r. i have a service manual for it. covers a lot of issues. EXCEPT disassembly of the glass. have wiring diagram for the power windows. yet the manual does NOT cover glass issues or outside trim issues. im sure ppls have delt with...

need to take out rear side windows on a 46r with power windows. have no power, workin on resteration. any one have a schmatic on this issue?? im sure im not the only one to deal with this issue. the schmatic or detailed info would be great. knuck

is there a schmatic or any one knows how to take out the rear windows on a 46r. with power windows???? sure dont want to brake anything. also the windows are in the up possision. and do not have power to them. all help is needed. thanks knuck

looking for a 4 barrel intake for a 322 nailhead. any leads will be apprecated. thanks in advance. knuck. preferably not warped.

with the 322 nailhead and the many many choices in carburation. IE: 2 barrel,4 barrel,2 4's 3 duece's. get the idea??? what was the best setup did Buick use. for the best umph and mileage. let me know what you guys are doing out there. myself got a stromburg 2 barrel. it's iffy at best.