Search results

The console has been sold.

tommyboy submitted a new listing: 1964 Buick Skylark Convertibile - 1964 Buick Skylark Convertibile View the entire listing here...

1964 Buick Skylark conv. parts for sale , console, $500.00 + shipping,rear wheel chrome ,needs work, $100.00 + shipping pinch weld chrome , needs some work,$75.00+ shipping. I also have A?C stuff vent balls, suitcase, condenser, under dash venting. The console has been sold

tommyboy submitted a new listing: 1964 buick skylark parts - 1964 buick skylark parts View the entire listing here...

My car was in a collision, ins. has it now. I have some extra parts I no longer need. 1- left front fender 1- Iron board console. 1- New top 1- NOS left headlight door. 1- NOS tissue dispenser. 1- used conv. top assembly (what the top attaches to) 1- used A/C system, ducts, suitcase, vent balls...

tommyboy submitted a new listing: left over parts call for list & price - left over parts call for list & price View the entire listing here...

tommyboy submitted a new listing: 1964 Buick skylark parts - 1964 Buick skylark parts View the entire listing here...

Hi, I am in a desperate situation. My car was T boned by a Century Link F5? Work truck I am looking for any information on body dimensions, as I believe I will be doing the work myself. I am hoping someone in the community has done a rotisserie restoration, and may can give me the specks for...

Hi all, Any body know how to properly adjust the relationship between the switch pitch torque convertor switch on the intake manifold, and the throttle dash pot on the carb. The problem I am having is this; If I get the correct length on the trans. switch then I am unable to get full throttle...

Hello, I have a very bad situation that has just developed in my newly rebuilt 1964 buick 300. At first it ran great, and I thought I did a good job of breaking her in . When I start it , it sounds like piston slap and maybe detonation. As I raise the rpm all the clatter goes away until it gets...

Hello, Does anyone have or know where I can get the electric dash pot bracket( P/N 1365820 ,for a two barrel 300 engine? I am also looking for the correct switch pitch bracket( P/N 1365871) that mounts on the rear of the intake manifold. Thanks, Tom

Hello, Just finished rebuilding a 1964 Buick 300 . I ran it on the stand to make sure there were no leaks . I ran it three different times, but not more then 5min. each time Now it is in the car and I am not sure of the proper break in procedure. the ST 300 trans was also rebuilt , but it says...

A new Wanted listing has been posted by tommyboy: Super Turbine trans. The description for this listing is: -------------------------------------------------------------- Hello, Any one know where I could get the trans. filter pipe for a first design 1964 Buick super turbine transmission...

Hi, In my shop manual it states that the engine head bolt threads must be coated with GM Perfect seal sealing compound. Have any of you Buick 300 guys used this, and is there a a substitute? I know that all the block holes are blind, so I am not sure what I am sealing here. I have some silver...

Hi, I have a 1964 Buick Skylark Conv. I am rebuilding the engine, and trans. I noticed that there are no valve seals on the heads, and no mention of them in my Chassis manual. Can some one tell me why this is the case? Thanks, Tom:confused:

Hi, I have a 1964 buick ST 300 Trans. I am rebuilding I seem to have lost one of the reverse piston springs :clonk: it is green is there any other spring from a similar trans. that would work,? anyone out there know where I could find one?:confused: Thanks Tom

Hi, Just joined I have a 64 Buick skylark convert, I am currently rebuilding engine, trans. and installing oem A/C any one have access to the templates needed to do the job?:shield: