Search results

  1. T

    Buick 455 430 400 and 350 parts

    I just wanted to touch base with few folks and see what the interest for more reasonable priced Buick parts. I have been in contact with a manufacturing facility that is USA based and has produced these parts. These are performance parts with a name to go behind it. I know you have heard rumors...
  2. T

    Buick Brotherhood, sounds cheezy but it exsits!

    I thought I would share with you guys an experience I had today that left me dumbfounded. I had posted an ad on craigslist with a list of parts I needed for my 455 that I am currently working on. It was a shot in the dark, but I figured that it was worth a shot before dumping a ton of money on...
  3. T

    Need a few parts for a 455, if you have them pipe up!

    I need one driver side rocker arm, the aluminum one. not hard to find but I dont need 16 of them. Thanks, I am also shopping for an aluminum intake and a pointless distributor. Thanks.
  4. T

    Cowl Induction Hood For a 66/67 Skylark?? I want one!

    Ok guys, Ive seen numerous 66 Skylarks with cowl induction hoods, and I want one. Its the same hood I've seen on a few cars so I dont think its fabricated. SOME ONE PUT THIS HOOD ON THE MAP! Im not the only one asking about this. Troy
  5. T

    Cam selection. Come on you know this is important......put in your 2 cents!

    Hey fellas, Its been awhile. My computer took a little spill of my bed while visiting New London awhile back and I finally got if fixed up. In any case, Ive been collecting parts for my 455 and I have come to a cross road in my build. I have selected the TA performance SP1 intake manifold and...
  6. T

    Wheel Moldings for a 66 Skylark

    Does anybody know if wheel molding from a 66-67 GTO will fit a 66 Skylark? I know the bodys are very simular....If so you can pick up a set of 4 wheel moldings for 150 bucks. That would save me time and money hunting down buick wheel moldings.
  7. T

    66 skylark dash console question

    Im stripping out my 66 Skylark to get it ready for paint this spring but I can seem to figure out how to take the dash console out. I removed the screws for the Dash pad and heater controls but nothing is budging.
  8. T

    455 Pistons?

    Ok, heres the deal. I have a 1970 455 with the 25cc dish pistons and a set of 68cc heads with the standard valves. I was looking into the Speed Pro pistons to increase the compression. After a little research I notice that Speed Pro pistons are 23cc dish. Not much of an improvement for 250...
  9. T

    In need of a good Machine Shop near Portland,ORI

    If anyone knows of a good machinist that has dealt with buick engines before please let me know. Thanks.
  10. T

    300ci 4bbl aluminum intake

    I have an original 4bbl aluminum intake for a 300ci Buick. I purchaced it for a project but have decide to go a different route. Best one Ive ever seen looks brand new. Any interest? Ill be placing it on ebay soon but I can give you a heads up...
  11. T

    Barn yard find

    I recently moved to Oregon from Texas, and with al the rain and cold i had to find something to do with myself. So I located this 66 Buick Special Deluxe in Tigard, OR for 2k. I thought it was a good buy seem how it ran good and just needed the brakes bled. It was actually sitting in a old barn...
  12. T

    A stroke of luck

    Hey there fellow Buick fans, I m new to this board of course, and really excited about my recent project. When I was about 15 I remember going though my dads old repair manuals and look at the difference between engine block torque and HP output from a variatity of engines. The reason we were...
Back
Top